Votes - 2, Average rating: 3.5
(
)
)
|
manual abstract
It is possible that you will need to manually override your security system if the transmitter becomes lost, or inoperative due to battery failure. Reading the sections on "MANUALLY OVERRIDING YOUR SYSTEM" is necessary to fully understand the procedure required to enable your vehicle in such situations. In addition, the chart on the last page of this manual has a section for the particular features and options installed in your vehicle as well as the override method selected. Valet Switch manual override is pre-selected from the factory, however, the system can be configured for "Custom Code" operation. Confirm the override mode selected on the last page of this manual, and familiarize yourself with the selection on it's operation. FEATURES : . 1 Five Button Programmable RF Transmitters 1 Five Button Programmable Transceiver . Five Channel Receiver (Capable Of Accepting Up To 4 Transmitters) . Code Hopping Technology . Selectable Manual Override Mode . Remote Panic in all modes . Protected Valet . User Programmable Manual Override Code . 7 Function LED (Light Emitting Diode) - Arm / Disarm / Zone 1, 2, 3 / Valet / Arming . Intrusion Alert with Memory Audible Arm / Disarm / Defective Zone / Tamper Confirmation Instant Siren Activation Starter Disable Additional Engine Immobilizer Output (optional relay required) True Last Door Arming (hardwire only) Defective Zone By-Pass Hardwire or Voltage Sense Selectable Active or Passive Arming Selectable Programmable Auto Lock On / Off Programmable Auto Unlock On / Off Programmable Door Lock Pulse Duration 1 Second / 3.5 Seconds/1 Sec L/ Dbl. U/L Programmable Active or Passive Door Locks User Programmable Permanent Chirp Delete On Command RF Chirp Delete from Transmitter 6 Tone Multi Tone Siren RF Inhibit with ignition on Parking Light Flasher Plug In Dual Stage Shock Sensor OPTIONS: Remote Trunk Release ( must have electronic trunk release ) Remote Keyless Entry ( must have power door locks ) Multiple Vehicle Capable Remote Starter Remote Power Window Roll Up Remote Garage Door Interface Two Step Unlock Configurable Headlight Illumination During Arming, Disarming, Or Both 128-7406 1 of 16 YOUR “ Code Hopping “ TRANSMITTERSThe transmitters included with your new security system use the most advanced and secure form of radio frequency transmission available on anycurrent automotive security system. Some of today’s sophisticated autothieves use a device known as a code grabber, which will receive and storethe signal from your keychain transmitter, and retransmit at a later time todisarm your system. Your anti code hopping transmitters will change their signal every time thebutton is pressed, so when a thief grabs then retransmits your signal, thealarm system will notrespond. If your transmitter button is pressed more than fifty times while it is out ofrange of the vehicle ( children playing with your keys ), the transmitter willnot operate when you return to the vehicle and will need to be realigned tothe receiver. To do this, simply press the lock button two times within a onesecond time period. The system will now respond to that transmitter eachtime a button is pressed. NOTE: Your system has the option of using a siren, the vehicle horn, or bothfor the sounding device. Where the siren is referenced below, thehorn or both may in fact chirp, or beep. Your System is also packaged with a two way confirming transmittershown left which can be set for Icon mode or text mode to indicate the function and status of your vehicle. To change modes, press and hold the "F" button for 5seconds. This puts the transmitter into the program mode. The program modes lets you make selections by pressingthe Trunk/Key Icon button to scroll up, or the Option buttonto scroll down. Once you come to the selection of choice, press the "F" button to select the option, and then use theTrunk/Key, Option, or lock/unlock buttons to toggle betweenchoices. Example: To change between text or icon modes, do thefollowing: 1) Press the "F" button for 5 seconds until the transmitterbeeps. 2) Press the Trunk/Key button until Homepage Select Set appears. 3) Press "F" to display the selections of text or icons. 4) Use the Trunk/Key or Option buttons to toggle between text or iconmodes. 5) Use the "F" key to select. 6) Press the "F" button for 5 seconds to exit the program mode. Other features that are selectable or programmable on your two waytransmitter are: (a) Alarm Trigger History (Will display the last 4 trigger events) (b) You can assign a Name for a output channel function (c) You can personalize the Homepage to display name, or have the digitalclock displayed YOUR “ Code Hopping “ TRANSMITTERSThe transmitters included with your new security system use the most advanced and secure form of radio frequency transmission available on anycurrent automotive security system. Some of today’s sophisticated autothieves use a device known as a code grabber, which will receive and storethe ...