Votes - 4, Average rating: 4.5
(
)
)
|
Other manuals for this model:
manual abstract
Some buttons on editing equipment may operate differently from those on the camera. Notes: • m (LANC) is a trademark. It stands for Local Application Control Bus System. • We cannot guarantee the results when connecting to equipment not bearing the LANC m symbol. E REMOTE Editing 85 E Dubbing to/from a Cassette with Digital Video Equipment Digital video equipment fitted with the DV terminal lets you edit, copy and transfer data digitally, with virtually no generation loss in image and sound quality. The DV terminal is for both line-in and line-out, since a single DV cable can handle data in both directions. • If a digital VCR is connected and an anomalous signal is sent from the VCR, the images recorded on the tape may also be anomalous (although it may not appear so on the TV image), or not recorded at all. • You are unable to dub tapes recorded with the copyright protective signal. • You cannot dub a tape recorded in .SP or .LP modes. REC AUDIO DUB. AV INSERT Signal flow AUDIO MONITER REC PAUSE AUDIO DUB. SEARCH SELECT MIX BALANCE ST-2ST-1 REW PAUSE SLOW PLAY STOP FF 2+ Preparations Example dubbing to the camera 1. Connect the camera and the other digital device. • Connect the Canon CV-150F DV cable (optional) with the sides of the plugs marked with the arrows facing as shown above. 2. Prepare the other device. • Turn on the power and load a recorded cassette. 3. Turn the camera’s POWER dial to VCR. • DV IN appears in the viewfinder. 4. Load a blank cassette. Editing 86 Dubbing 1. Find a point on your recorded cassette slightly before the section you want to copy and set it to playback pause mode. 2. Press the camera’s REC PAUSE button. • The camcorder enters record pause mode. 3. Start playback on the other digital device while you monitor the picture. 4. Press the play/pause e/a button on the camera body or the PAUSE a on the wireless controller. • Recording starts. 5. When you get to the point where you want to stop recording, press the stop button or the pause button. • Recording stops. 6. Stop playback on the other device. Notes: • If the cable is not connected properly, or if the cable is unconnected when you press REC PAUSE, the camera displays the caution ‘‘CHECK THE DV INPUT.’’ An anomalous image may also flash onto the screen. • Blanks between recordings on the playback tape are recorded as anomalous images on the tape that is being recorded to. Copyright signal Certain pre-recorded software tapes are copyright protected. If you try to play back such a cassette, “COPYRIGHT PROTECTED PLAYBACK IS RESTRICTED” appears in the viewfinder for a few seconds and then the camera displays a blank blue screen; you cannot view the contents of the cassette. If you try to record from such a tape via the digital cable “COPYRIGHT PROTECTED DUBBING RESTRICTED” appears in the viewfinder; you cannot record the contents of the tape. E Editing 87 Recording from a VCR, TV or Analog Camera (Analog Line-in) E You can record a video played on your VCR or analog camcorder (for digital camcorder, see p. 86) or a TV program onto a tape in the XL1S, if the TV or other device has audio/video outputs. • By selecting the 12bit ST-1,2 of the AUDIO MODE from VCR SET UP of the VCR menu, you can record 4 channels. • If an anomalous signal is sent from the TV or VCR, the images recorded on the tape may also be anomalous (although it may not appear so on the TV image), not recorded at all, or COPYRIGHT PROTECTED DUBBING RESTRICTED may appear in the viewfinder. • You are unable to dub tapes recorded with the copyright protective signal. Signal flow RECAUDIO DUB.AV INSERT L R V S STV-150 Stereo Video Cable S-150 S-video Cable S-VIDEO VIDEO R L AUDIO Preparations 1. Connect the camera to the VCR, TV or other camera. 2. Prepare the device. (Example connecting to the VCR) • Set the TV/Video selector on the television to Video. For further details, see “Connections for Playback on a TV Screen” on p. 83. • Turn on the VCR. Load your recorded cassette, and put the VCR in playback pause mode. • See your TV and VCR instruction manuals for details. 3. Turn the camera’s POWER dial to VCR. 4. Slide the INPUT SELECT switch to AUDIO 1. 5. Select LINE of the AUDIO1 IN from VCR SET UP of the VCR menu. 6. Load a blank cassette. Editing 88 Dubbing 1. Find a point on your recorded cassette slightly before the section you want to copy and set it to playback pause mode. 2. Press the REC PAUSE button. • S-video and audio IN/OUT terminals work as input terminals. • The camera enters record pause mode. 3. Start playback on the other device or turn on the TV to see the desired program while you monitor the picture. 4. Press the play pause e/a button on the camera body or PAUSE a button on the wireless controller. • Recording starts. 5. When you get to the point where you want to stop recording, press the stop button or the pause button. • Recording stops. 6. Stop playback on the other device. Note: • You can monitor the picture in the viewfinder. E Editing 89...