|
Other manuals for this model:
manual abstract
USING THE ACCESSORIES Attaching a Grip Belt Insert your right hand from the bottom of memory camcorder up to the base of your thumb. Put your hand in a position where you can easily operate the Recording start/stop button and the Zoom lever. Adjust the length of grip belt so that the memory camcorder is stable when you press the Recording start/stop button with your thumb. 1. Detach the belt. 2. Adjust the length of grip belt. 3. Attach the belt. Angle Adjustment This memory camcorder has a new swivel handgrip. Its handle turns along with the shooting angle. You can now shoot videos freely from high angles to low angles while standing. Rotate the swivel hand-grip at the most convenient angle. You can rotate it downward up to 180 degrees. Please be careful not to turn the swivel handle backward as it may cause damage. • • • • • 1 2 3 Using the Cradle (VP-MX20C/MX20CH only) • Link the memory camcorder to a computer or a TV with the cradle The memory camcorder can be easily linked to a PC, TV or any other devices with the cradle. This keeps the camcorder safe, can recharge the battery and links it to TVs, AVs and USBs. Very convenient. • You have to connect the AC power adaptor to the cradle when connecting external devices using the cradle. DC IN jack USB jack AV jack Cradle Receptacle • If you connect your memory camcorder to the provided cradle using more than one type of output cable, the order of output signal is as follows: USB cable .. AV cable. • If you connect the camcorder to the cradle, the connection jack on the camcorder itself (USB and AV jacks) will not output a signal. • Do not connect the connection cables to memory camcorder and cradle at the same time, it may cause conflict and may not work properly. If this occurs, remove all the connected cables and try the connection again. English_13 preparation CONNECTING A POWER SOURCE • There are two types of power source that can be connected to your memory camcorder. • Do not use provided power supply units with other equipment. -The battery pack: used for outdoor recording. -The AC power adaptor : used for indoor recording and playing back. ..page 21 Battery Pack installation / ejection It is recommended you purchase one or more additional battery packs to allow continuous use of your memory camcorder. Inserting the battery pack 1. Slide and open the battery slot cover as shown in the diagram. 2. Insert the battery pack into the battery slot until it softly clicks. • Make sure that the SAMSUNG logo is facing up while the set is placed as shown in the diagram. 3. Slide and close the battery slot cover. Ejecting the battery pack 1. Slide and open the battery slot cover and push the battery lock. • Gently push the battery lock in the direction as shown in the diagram to eject the battery out. 2. Pull the ejected battery out in the direction as shown in the diagram. 3. Slide and close the battery slot cover. English_14 CARD CARD CARD Insert Eject Charging the Battery Pack • Be sure to charge the battery pack before you start using your memory camcorder. • Use IA-BP85ST battery pack only. • The battery pack may be charged a little at the time of purchase. 1. Slide the POWER switch downward to turn off the power. 2. Open the LCD screen and insert the battery pack to the memory camcorder. ..page 14 3. Open the DC IN/USB/AV jack cover. 4. Connect the AC power adaptor to the DC IN jack of your memory camcorder. 5. Connect the AC power adaptor to a wall socket. • The CHG (charging) indicator lights up in orange and showing that the battery pack is charging. • The CHG (charging) indicator lights up in green when the battery is fully charged. ..page 16 6. When the battery pack is fully charged, disconnect the AC power adaptor from the memory camcorder. • Even with the power switched off, the battery pack will still discharge if it is left attached to the memory camcorder. It is recommended that you remove the battery pack from the memory camcorder. D 1 5 4 2 You can also charge with the cradle. ..page 13 English_15 preparation Charging indicator Tips for battery identification ....The colour of the LED indicates charging status. • If the battery has been fully charged, the charge indicator is green. • If you are charging the battery, the colour of the charge indicator is orange. • If an error occurs while the battery pack in charging, the charging indicator blinks red.
Cameras - VP-MX20 (7.47 mb)
Cameras - VP-MX20C (7.47 mb)
Cameras - VP-MX20CH (7.47 mb)
Cameras - VP-MX20L (7.47 mb)