Votes - 1, Average rating: 3 ( )

Manafacture: Hitachi File size: 2.09 mb File name: Language of manual:

• If you make a mistake when entering digits, press the CLEAR button repeatedly to display "-" for the incorrect digit, then reenter the correct digit. 6 Enter the start time by pressing (0), (6), (0) and (0) for 6:00. Remote Control Illustration. 7 Press the (2) button for PM. 8 Enter the end time by pressing (0), (6), (3) and (0) for 6:30. The VCR automatically selects PM for you. 9 Enter the recording date by pressing (0), (7), (1) and (0) for 7/10/98. Remote Control Illustration. 10 Press the TAPE SPEED button to select the recording speed EP. 11 Press the PROGRAM button to set the program in memory. 12 Press the POWER button to turn off the VCR. The delayed recording indicator will display on the VCR. This tells you that the VCR will automatically record at the times and dates you have programmed. Note: If a cassette has not been inserted or a cassette without safety tab has been inserted, the delayed recording indictor will flash to warn you. The cassette without safety tab will be ejected automatically. Be sure to insert a cassette with safety tab intact. When you have set up all the timed recordings you want: • Don't forget to load a videocassette (with the safety tab still attached) to record on. • If you have installed a cable box (see page 26), turn on the cable box and select the channel you want to record on the cable box (08 in this case) before recording starts. Note: You can correct any item entered as you go by pressing the CLEAR button repeatedly until the digit to be corrected changes to white dash "-" on the screen. Then enter the correct number. Illogical times and dates won't be accepted. To stop recording while in the timed recording mode: 1 Press POWER button. 2 Press the STOP button within 10 seconds. • This can be done either on the VCR or with the remote control. Remote Control Illustration. Important: Your timed recording settings take effect when you turn off the power on the VCR. USING THE VCR PLUS+ SYSTEM FOR RECORDING USING THE VCR PLUS+ SYSTEM FOR RECORDING • About the VCR Plus+ system This handy feature makes timed recording a snap. You don't need to enter the specific channel, date, time or duration of a program. All you enter is its PlusCode programming number - a number of up to eight digits. This special code is easy to find in your favorite TV program guide or daily newspaper. Here's a sample page from TV Guide showing PlusCode numbers next to each program. Your local channels may be different from the VCR Plus+ channel codes. To get ready to record with the VCR Plus+ system you need to assign your local broadcast and cable channel numbers to the VCR Plus+ channel codes already stored in your VCR's memory. This is called channel setup and you do it using the on-screen Easy Guide System and the following step-by-step instructions. Then you will be ready to begin VCR Plus+ recording, also using the on-screen Easy Guide System. VCR Plus+ and PlusCode are trademarks of Gemstar Development corp. • Channel setup Before you begin 1 Look for a listing like this one in your local TV program guide or Sunday newspaper TV section. Notice the small numbers to the right of the station name. These are the VCR Plus+ channel numbers that you will use in the channel setup procedure. 2 Make a list of the VCR Plus+ channel numbers and the channel numbers you are receiving them on. If there are any difference, YOUR channel numbers must be assigned to the corresponding VCR Plus+ number. (See Example) Note in the example that the channel numbers are the same except for 20 (received on channel 8) and 42 (received on channel 38). These two channels must be assigned. EASY DELAYED RECORDING WITH THE VCR PLUS+ SYSTEM This setup should be performed if you are using an Antenna or Cable without a cable box. (Hookups [A], [B], [C] or [D].) If you receive all your channels through a cable box (Hookups [E], [F] or [G]) please refer to page 26 "cable box setup" in "First Time Setup" section. The following operation is not necessary. • VCR Plus+ setup - Channel setup The following shows the procedure you should perform when you are receiving the Cable News Network (channel 42 with the VCR Plus+ system) on channel 38. Matching Broadcast CH Numbers to VCR Plus+ Channels 1 Turn on the TV and select the Video channel (3 or 4). Or, if you are hooked up with an audio/video cable, set the TV to AUX or VIDEO. 2 Press the GUIDE button. The main on-screen menu will appear on the TV screen. Remote Control Illustration. 3 Press the (4) button to select CHANNEL PRESET. Note: If you have set up the cable box, the following operation is not necessary. 4 Press the (4) button to select VCR PLUS+ SETUP. A small arrow points to a blank "--" in the CHANNEL column. Note: If your broadcast channel number is the same as the VCR Plus+ Channel in your TV listing do not enter any number. 5 Press the CH ( / ) button to move up and down through the channel list until you reach VCR Plus+ CH42. 6 Press the number buttons to assign yo...

Download now

Please, enter two numbers from picture: