Votes - 1, Average rating: 4
(
)
)
|
manual abstract
8. Level Dependent Compensation Level Setting [Level Dependent: 0% to 25%] Screen noise due to the detail of dark parts of an object can be reduced. If level dependent compensation level is set too high, however, hair, for example, will be reproduced less sharply. 9. Dark Detail Compensation Level Setting [Dark Detail: 0 to 5] The contours of the darker portions of an object can be emphasized. This setting is possible only when the Level Dependent Compensation Level Setting (9-9) is set to 0 %. 10. Chroma Detail Compensation Level Setting [Chroma Detail: 0 to 15] The contours of high-hue portions of an object can be emphasized. 11. Flesh DTL Level Setting [Flesh DTL Level: Low, Mid, High] LOW: The roughness of the flesh tones is minimized. MID: This is the standard setting. HIGH: The outlines of the flesh tones are accentuated. 12. Corner Detail Setting [Corner Detail: OFF, ON] Corner detail, which improves the resolution of corners, can be turned on or off when the Detail Level Setting (9-1) is at HIGH or LOW. 13. Precision Detail Level Setting [Precision Detail: OFF, LOW, HIGH] This setting is to narrow detail width and suppress detail glare. -50 : Color Matrix Set Display B_Mg Gain: Increases or decreases the intermediate color between blue and magenta. B_Mg Phase: Varies the hue of the intermediate color between blue and magenta. Mg Gain: Increases or decreases the magenta. Mg Phase: Varies the hue of the magenta. Mg_R Gain: Increases or decreases the intermediate color between magenta and red. Mg_R Phase: Varies the hue of the intermediate color between magenta and red. R Gain: Increases or decreases the red. R Phase: Varies the hue of the red. R_Yl Gain: Increases or decreases the intermediate color between red and yellow. R_Yl Phase: Varies the hue of the intermediate color between red and yellow. Yl Gain: Increases or decreases the intermediate color of yellow. Yl Phase: Varies the hue of the yellow. Yl_G Gain: Increases or decreases the intermediate color between yellow and green. Yl_G Phase: Varies the hue of the intermediate color between yellow and green. G Gain: Increases or decreases the green. G Phase: Varies the hue of the green. G_Cy Gain: Increases or decreases the intermediate color between green and cyan. G_Cy Phase: Varies the hue of the intermediate color between green and cyan. Cy Gain: Increases or decreases the cyan. Cy Phase: Varies the hue of the cyan. Cy_B Gain: Increases or decreases the intermedi ate color between cyan and blue. Cy_B Phase: Varies the hue of the intermediate color between cyan and blue. B Gain: Increases or decreases the intermediate color between blue and magenta. B Phase: Varies the hue of the intermediate color between blue and magenta. -51 ; Other Set Display 1. Gamma Correction Level Setting [Gamma: 0.35 to 0.55] Gamma correction level can be set. 2. Knee Compensation Level Setting [Knee Point: 88% to 98%, Dynamic] 88% to 98%: The level of video signals subject to knee compensation (knee point) can be set. Dynamic: Knee compensation level is automatically adjusted according to the scene. 3. White Clip Level Setting [White Clip: 95% to 110%] The peak level of video signals to be white-clipped can be set. 4. Flare Correction Level Setting [Flare R/G/B: 0 to 100] Flare correction level can be adjusted. . Flare correction level has already been adjusted prior to shipment from the factory. 5. Black Stretch Setting [Black Stretch: ON, OFF] Black stretch to correct the suppression of black portions at low luminance can be set to ON or OFF. 6. Clean DNR Setting [Clean DNR: HIGH, LOW, OFF] This enables the clean DNR effect to be selected. 7. 3D-DNR Setting [3D-DNR: OFF, Low, Mid, High] This enables the 3D-DNR effect to be selected. . When “Mid” or “High” is selected, the noise is reduced but lag increases. 8. 2-dimensional Lowpass Filter Setting [2D LPF: OFF, LOW, HIGH] The 2D lowpass filter that reduces moire and cross color can be set. 9. CCD Read Out Mode Setting [Field/Frame: Field, Frame 1, Frame 2] Field: CCD storage will be by field storage. Frame 1: Vertical resolution increases in frame storage. Frame 2: Vertical resolution is raised without increasing residual images by frame storage and electronic shutter. 10. PC Control Access Speed Setting [Baud Rate: 1 200bps, 2 400bps, 4 800bps, 9 600bps] This setting is to select a communication speed in controlling the camera from the computer. -52 11. Component Output Setting [Component: RGB, Y/Pr/Pb, Y/C] This enables RGB, Y/Pr/Pb or Y/C to be selected as the component signals which are to be output from the I/F REMOTE connector. 12. Digital Extender Setting [Digital Extender: OFF, ON] OFF: Under normal circumstances, this setting is used. ON: An extender effect which is approximately 1.5 times greater is achieved. However, the resolution drops when the digital extender is set to “ON”. 13. Fan Setting [Fan: OFF, Auto] (models AW-E750, AW-E655) OFF: Select this setting to stop the fan when its operating sound is f...