Votes - 2, Average rating: 3.5
(
)
)
|
manual abstract
© Press STILL where you want to continue recording. Set POWER to CAMERA. Press RECORD/PAUSE to resume recording. 24 Camera Recording Programmed Recording Set a recording start and stop time. Or, set a 5 or 10 second interval recording to be done each minute. Before you begin... • Connect Camcorder to power source. Use AC Adaptor for longer recordings. • Insert cassette with record tab (page 13). • Set POWER to CAMERA. 12 3 1 r~ 10MIN. — 20MIN. — 30MIN. —TO TAPE END INTERVAL*2 10 SEC/MIN. INTERVAL 5 SEC/M IN. *1 Interval 5 SEC/MIN: Record 5 seconds each minute. *2 Interval 10 SEC/MIN: Record 10 seconds each minute. Press MENU for MENU mode. Press UP A or DOWN ▼ to select PROGRAMMED - - - MENU - ■ - PAGE 1/2 H=Eä2 sa TITLE TALLY LAMP STANO-BY RELEASE CLOCK SET AUTOMANUAL SELECT SET END PUSH T/A KEY PUSH DISPLAY KEY PUSH MENU KEY Press DISPLAY. (Current time is displayed.) Each additional press of DISPLAY increases start time by 30 minutes. ; 10:20PM REC TIME ; 1QMIN. SELECT : PUSH T/A KEY SET : PUSH DISPLAY KEY START : PUSH RECORD KEY CANCEL PUSH MENU KEY Press DOWN ▼ to select EBIB. Press DISPLAY repeatedly to select one of the options shown at the left. STAffT ; 1Û : 20PM rreiïïïTa ; 10MIN. SELECT : PUSH T/A KEY SET : PUSH 04SPLAY KEY START : PUSH RECORO KEY CANCEÜ PUSH MENU KEY To cancel the setup, press MENU twice. Press RECORD/PAUSE to place Camcorder in stand-by mode. Note: • Start time may not be set over 24 hours from current time. • Camcorder shuts off at tape end, or 12 hours after Interval Recording starts. • To cancel, set POWER to OFF. STAND-BY START : 1020PM REC TIME ; 10MfN, T0:20:00PM UN 12000 j Recording will be done as scheduled 25 Playing Back Recordings Playback on EVF or LCD Monitor Before you begin... • Connect Camcorder to power source. • Insert recorded tape. Press LCD-OPEN and swing LCD monitor fully open. • If you want to playback on EVF, close and lock LCD monitor. Set POWER to VCR. Power lamp lights. • If tape has no record tab, auto playback begins. • EVF or LCD monitor turns on/off by the POWER switch. • EVF shuts off when LCD monitor is opened and turns back on when LCD is closed. Playback function buttons. o REWiind) : rewind tape. © PLAY : play tape. 6» STOP : stop tape. ft BRIGHT : adjust LCD monitor brightness. ft VOLUME : Adjust volume of speaker. Press “T” : Volume up(+). Press “W” : Volume down(-). VOLUME [-] Mil----[+] Note: • Using LCD monitor reduces battery operating time. • Return LCD monitor to locked position when not in use. 26 Playing Back Recordings 1/2 Slow Play Available only with SP recordings made on this Palmcorder. Before you begin... • Connect Palmcorder to power source. • Insert tape recorded in SP mode. • Set POWER to VCR. 1 During playback, press PLAY for 1/2 Slow Play mode. Audio is muted. • Picture noise will occur in 1/2 slow play. • If the recorded speed changes from SP to SLP, normal speed playback is resumed. AUDIO IS MUTED Press PLAY again to resume normal speed playback. Note: Vertical jitter may occur during playback. Skew may occur at top of picture. 27 Playing Back Recordings Special Effects 3 times normal. 9 times normal. Before you begin... • Connect Palmcorder to power source. • Insert recorded tape. • Set POWER to VCR. Quick Visual Search Search Speed SP (Standard Play) SLP (Super Long Play) During playback, press: FF : fast forward search REW : rewind search Press again or press PLAY for normal play. Still Picture Press STILL to freeze picture. Press again for normal play. (PV-L680 shown) Note: • During search, horizontal noise bars will appear. Audio is muted. • To protect video heads and tape, operating modes will revert as follows after 5 minutes: Still-►Stand-by Stand-by —►Power off (when Battery Pack is used). • Tape auto-rewinds if played or fast forwarded to end. Tracking Control 30^ v y 28 Auto Tracking Continuously analyzes each recording for optimum picture quality. Manual Tracking Some recordings require manual adjustment to reduce noise. In Playback mode: Press UP A or DOWN ▼ until Playback picture clears up. Press DISPLAY to return to Auto Tracking. In Still mode: Press UP A or DOWN ▼ until Still picture clears up. Press DISPLAY to return to Auto Tracking. V-Lock Control Reduces jitter in Still mode. Hold down DISPLAY and UP A or DOWN ▼ until picture is stable. Playing Back Recordings TV Playback or Viewing Connect Camcorder to a TV to view playback or recordings in progress. TV with AUDIO/VIDEO IN Jacks. To Audio In Audio/Video Cable (Supplied) (PV-L680 shown) To Audio/Video Out To Audio/ Video Out Before you begin... • Connect Camcorder to power source. • Make all TV-Camcorder connections. Set POWER to: VCR -* view playback. CAMERA -* view picture as it is recorded. Turn TV ON and set to LINE INPUT. See TV owner’s manual. Begin playback or recording. Ç T...