Votes - 2, Average rating: 4
(
)
)
|
manual abstract
First, disconnect the cable from the TV and connect it to the VCP. Then connect the VCP to the TV. 10 4C61501A E/P08-15 10 9/13/01, 2:19 PM I I I I I I m POWER SOURCE DC POWER SUPPLY A DC car cord is supplied with the unit. The car cord has been designed for use with external DC power (12 volt with negative ground). Plug one small plug into the DC input jack on the rear of the VCP, then plug into the one jack of the Dual input DC car adapter (not supplied) connected to the car cigarette lighter socket. If you use a TV with DC power, connect to another jack of a dual input DC car adapter. Make sue that the cord makes a firm connection. It may be necessary to try several insertions, rotating the plug for proper electrical connection. NOTE: • ALWAYS TURN OFF VCP FIRST BEFORE SWITCH ON OR OFF THE IGNITION OF CAR ENGINE. • Make sure that the negative terminal of the battery is grounded. This set is designed for use with negative ground system only. • Use the supplied car cord only. • When the VCP is not in use, always disconnect it from the car cigarette lighter socket to avoid a battery drain. • If the VCP is to be directly connected to a 12V DC power source, for example, recreational vehicle (RV) applications, make sure the power cord is connected after the ignition switch to avoid battery drain. • Do not operate the VCP if the car battery is weak. Peak current from the car alternator could blow the DC fuse. • In case of connecting to the TV (Memorex MT1098), refer to its owner’s manual. • Check the battery’s charge level regularly when the VCP is used in a vehicle. REPLACING THE FUSE IN THE CAR BATTERY CORD PLUG If the fuse in the car battery cord plug blows, replace it with a new 8 A fuse (Fast Blow Type) as shown below. Unscrew the tip of the plug to remove. PLUG 8A FUSE Q2_n 11 4C61501A E/P08-15 9/13/01, 2:19 PM ENGLISH ^■mm >- ■ ■ miii SETTING THE VIDEO CHANNEL To view playback of a recorded tape, the TV must be set to channel 3 or 4 (video channel). The VCP 3/4 Channel Selector switch must also be set to channel 3 or 4 as shown below. If you have used a Audio/Video cable you should not have to follow this procedure. Simply select the VIDEO mode on your TV. Press the POWER button to turn the unit on. POWER Set the 3/4 Channel selector switch to CH 3 or 4. .CH i IN© OUT IN ( RF OUT ( 2 3 4 CH 0-e-® DC (—) 12V 2 '^«"Tum'oNlhe'TV'and'setto'cHs'o'Tto'correspond'wthlheThanneTseiectorin"'^ / \ 3 or 4 For a push-button TV tuner If CH 3 or 4, corresponding to the video channel cannot be tuned on your TV, or is not broadcasting in your area, proceed as follows: set the VCP 3/4 channel selector switch and the TV to CH 3 or 4. Play back a prerecorded tape and tune the TV to receive a sharp color picture from the video cassette player. Refer to your TV owner’s manual for details. 12 4C61501A E/P08-15 12 9/13/01, 2:19 PM ■■■ i i i i i i i i 4- ■ ■ i i i LOADING AND UNLOADING THE VIDEO CASSETTE TAPE Use only video cassette tapes marked IVHS LOADING a Gently push the center of the tape until it is automatically retracted. AUTOMATIC POWER ON AND PLAY When loading a cassette tape, this video cassette player will turn on automatically and playback will start immediately.The POWER, and PLAY indicators will light. UNLOADING To unload a cassette, press the STOP/ EJECT button in the STOP mode. Remove the cassette. \ STOP/EJECT \ AUTOMATIC EJECT If the video cassette player automatically rewinds the tape to the beginning (AUTO REWIND FEATURE), the tape will be ejected automatically. NOTE: • Always eject the tape when not in use. • The cassette can be ejected even if the POWER button is "OFF" 13 2 1 2 4C61501A E/P08-15 13 9/13/01, 2:19 PM ENGLISH ■■■■ i i i rm 4- ■ ■ ■ i i i PLAYBACK TO START PLAYBACK Press the POWER button on the unit or on the remote control to turn the unit on and set the TV to the Video position. Load a prerecorded tape. (When loading a cassette tape, the video cassette player will turn on, the PLAY indicator will light and playback will start automatically.) A -f 2 POWER NOTE: To prevent damage to the tape, always turn off VCP first before you switch on or off the car engine ignition. 14 4C61501A E/P08-15 14 ^ 9/13/01, 2:19 PM TO REWIND OR FORWARD THE TAPE RAPIDLY Press the REW button in the STOP mode. REW® If you want to see the tape program during REW mode, press and hold the REW button. The backward visual search picture will be seen on the screen. Release to return to the REW mode. Press the F.FWD button in the STOP mode. If you want to see the tape program during fWd mode, press and hold the F. FWD button. The forward visual search picture will be seen on the screen. Release to return to the FWD mode. 5o 6o 7o 8o Q n QUICK O 0oVIEWoCALLO MENU - SET_ _ CD>-CD"CD [CD' RESET SLEEP ENTER I VOL CD CD I CD STOP □REPEAT mu ATR ▼ TRACKING i I I I I I I I I I VP POWER DIGITAL TRACKING CONTROLS f When a tape...