Votes - 3, Average rating: 4.7
(
)
)
|
manual abstract
To set the clock at any other time follow each of these steps: 1 Press MENU until the DUAL-DECK FEATURES menu appears. 2 Press “1” to select VCR SETTINGS/SET CLOCK. 3 Press “1” to select DISPLAY SETTINGS/CLOCK. 4 Press “1” to select SET CLOCK. 5 Press the number buttons to enter information as you are prompted by the blinking cursor. If you don’t need to change the information for a particular item, press to move to the next item. Set Month (1-12) January is “01”, October is “10”, etc. Set Year (0-99) Enter only the last two digits. For example “98” for “1998”. Set Day (1-31) Enter today’s date. For example, if today is the fourth, enter “04”. Set Hour (1-12) Enter only the hour. For example, if the time is 4:28, the hour is “04”. Set Minute (0-60) Enter only the minute. For example, if the time is 4:28, the minute is “28”. Set AM/PM (1-2) Enter “1” for AM or “2” for PM. Set Daylight Savings Time (1-2) Enter “1” for AUTO or “2” for OFF. AUTO will automatically add one hour on the first Sunday in April (“Spring forward”) and subtract one hour on the last Sunday in October (“Fall back”). 6 Press QUIT to save and exit the menu system, or press MENU to save and return to the DISPLAY SETTINGS menu. 1 2 4 It is important to set the Dual-Deck VCR’s internal clock to ensure accuracy on Timer Recordings and Date/Time Stamps. 3 4 Press 5 Press 6 Press 7 Press 1 2 3 4 You can change channels with the Channel Up/Down buttons or directly with the number keys. 4 Press 5 Press 6 Press 7 Press 1 2 3 4 You can change channels with the Channel Up/Down buttons or directly with the number keys. Setting Antenna & Channel Memory Your Dual-Deck VCR will automatically tune in all available TV Stations whether from Antenna reception or Cable (CATV). Simply indicate the Antenna Source and then run Auto Program: 1 Press MENU until the DUAL-DECK FEATURES menu appears. 2 Press “1” to select VCR SETTINGS/SET CLOCK. 3 Press “2” to select TUNER/CHANNEL LIST. repeatedly to set the ANTENNA SOURCE to Antenna or Cable. or to move the selection arrow to AUTO PROGRAM. to begin Auto Program. The VCR will cycle through all possible TV or cable channels and automatically place the channels you receive into Channel Memory. This will take a few minutes to complete. QUIT to exit the menu system or MENU to return to the VCR SETTINGS menu. Your channel list must have a minimum of 2 channels; one channel is not valid. If you are using a cable converter box, you will need to set your VCR’s tuner channel to receive only the cable converter box output channel (see p.39). Basic Tuner Settings Channel Selection • Tuning with the Channel Up/Down Buttons Press the CHANNEL Up/Down buttons on the remote control or on the Dual-Deck VCR’s front panel to move up or down to the desired channel. • Tuning with the Number Buttons For channels 1 through 9, press “0” then press the corresponding number button (1-9). If you are tuning to a channel higher than 100, press 100+ and then enter the last two digits. • Selecting Line 1 or Line 2 You can select Line 1 or Line 2 with the CHANNEL Up/Down buttons. Line inputs are located after the highest programmed station and before the lowest programmed station. When you select Line 1 or Line 2, you will see the input (if any) from additional video equipment connected to your Front or Rear Audio/Video inputs. CHAPTER 3 - INITIAL SETTINGS 17 You can manually Add and Delete Channels in the Tuner/ Channel List menu. You can manually Add and Delete Channels in the Tuner/ Channel List menu. Adding or Deleting Channels The first time you set up your Dual-Deck VCR, you must use AUTO PROGRAM before you can manually add or delete channels. To add or delete channels manually: 1 From the TUNER/CHANNEL LIST menu, press the number keys to tune in the desired channel. 2 Press or to move the selection arrow to Add Channel or Delete Channel. 3 Press to add or delete the selected channel. 4 If you wish to add every channel, move the selection arrow to Add All Channels and press the key. 18 DUAL-DECK VCR USER'S GUIDE C H A P T E R 4 C H A P T E R 4 Copy Features Copying a Tape Copying tapes is what owning a Dual-Deck VCR is all about. Just follow these simple steps: 1 Insert your source tape into Deck 1 on the left side of the Dual-Deck VCR. 2 Insert your target tape into Deck 2 on the right side of your VCR. 3 Press COPY TAPE on the front panel of your Dual-Deck VCR or on your remote control. Your Dual-Deck VCR will begin copying from Deck 1 to Deck 2. Note: When you press Copy Tape, Deck 1 rewinds a few seconds (called “pre-roll”) and Deck 2 goes into Record Pause mode automatically before copying begins. This “synchro-start” results in the best possible quality when copying and editing. Turn EZ-Copy on or off in the Copy Tape Settings menu The Copy Tape button is your key to one- touch copies. 4 To pause the copying process, press . To resume, COPY TAPE STOP press COPY TAPE again. To stop the copying process, press on Deck 2. EZ-Copy EZ-Copy au...