Votes - 7, Average rating: 3.1
(
)
)
|
manual abstract
с кнопкой управления (нормально замкнутой на корпус) Открытие Закрытие Красный/черный 4 Голубой/красный Голубой/желтый Красный/желтый А Серый/красный Серый/желтый ъ* Открытие Блок центрального замка. Закрытие К кнопке центрального замка 16 Инструкция по установке Installation Manual General recommendations Before you get down to installation, disconnect the “ terminal of the car batteiy. 1. The main unit is to be installed inside the passenger compartment, away from sources of moisture and heat. 2. The RF Base Station with antenna is to be mounted on the windscreen as high as possible to reach maximal communication range between transceiver and vehicle. 3. The siren is installed in the engine compartment or in another location inaccessible for a thief, with the megaphone down or sideward. The location must be away from heat sources and protected from penetration of water. If the siren has a back-up battery, access to the service keyhole must be ensured. 4. The pin switches of the hood and trunk are mounted in locations protected from water and inaccessible when the hood/trunk is closed. 5. The shock sensor is installed inside the passenger compartment on the car body’s metal structures, as close to the car’s longitudinal axis as possible, and is fixed with screws or double sided mounting pad. 6. All high-power circuits should be fused for respective currents. Kit Contents Voltage Current Consumption RF Frequency Working Temperature Maximal Allowable Current via the Relay Contacts - Immobiliser Relay - Indicators Relay - Central Door Lock Relays Transmission Format Transceiver RF Range Conditions Pager Remote Control Built-up City Area 350 - 400m 250 - 300m Open Air within City Area 700 - 900m 400 - 450m Open Air outside City Area Up to 1500m Up to 800m 9...15V 20 mA 433,92 MHz -40...+85°C 30A 10A 15A AM/AM Two Way Car Alarm System MONGOOSE EMS 1,7R Ш System Programming Remote Code Learning The EMS 1.7R has one two-way Transceiver and one one-way transmitter in the standard kit, however the system can teach up to four transmitters/transceivers. To increase a number of remote controls to control the alarm system fulfill the below procedure: The basic procedure is the same regardless of single digit pin code or two-digit pin code. If the system has a single digit PIN code, follow steps 1-2 but skip steps 3-4. If the system has a two digit PIN code follow the entire procedure. 1. When the alarm system is disarmed turn the ignition on. 2. Press the override switch as many times as the first digit of the PIN code. 3. Cycle the ignition off/on. 4. Press the override switch as many times as the second digit of the PIN code. 5. Switch the ignition off. If the PIN code is correct one short and one long beep will confirm entering the Code Learning. 6. Switch the ignition on. 7. Press button 1 of each remote control you want to program to the system. One siren beep will confirm the transmitter code is learnt. When you are programming a two-way transmitter please wait a few seconds after the beep until the indicator icon on the LCD screen is flashing two times to confirm the main unit code has been programmed to the transceiver, otherwise the pager function will not work. 8. To exit the Code Learning switch the ignition off and press the override switch or wait for 15 seconds, a double siren beep will confirm that Code Learning has exited. NOTE: If you want to move to the Function Programming switch the ignition back on without pressing the override switch and before the double siren beep. Function programming. 1. Follow through with transmitter programming and turn the ignition back on (do not press the override switch in the above item 8!). 2. Press the override switch 4 times 3. Cycle the ignition off/on. 4. Press the override switch 6 times. 5. Press buttons 1 and 2 together. An audible signal will confirm the system has entered the Installer’s Function Programming. 6. Turn the ignition off/on. 7. Press the override switch as many times as the number of the software switches group (first digit). 8. Turn the ignition off/on. 9. Press the override switch as many times as the number of switch within the group (second digit). 0 Installation Manual СХЕМЫ ПОДКЛЮЧЕНИЯ К ЦЕНТРАЛЬНОМУ ЗАМКУ рис.2 Дополнительный электропривод и если Ц.З. нет рис.З Позитивное управление ЦЗ. рис.4 Негативное управление Ц.З. Открытие Закрытие f Красный/черный ¿ Голубой/красный çr^° Голубой/желтый Красный/желтый ¿ _ Серый/красный 9^° Серый/желтый ^ 1-5- ЗА Открытие Блок центрального замка. Закрытие рис.5 Пневмо Ц.З. (Audi, Mercedes) г (+зш 1—м— Красный/черный Ornoume 6 * Голубой/красный çr Голубой/желтый Красный/желтый ? -, ^ 0 А Серый/красный çr Серыи/желтыи 1 1-1-ЗА V. Автомобильная охранная система “MONGOOSE” Модель EMS 1.7R 15 РУССКИЙ СХЕМА ПОДКЛЮЧЕНИЙ коричневый оранжевый зеленый серый серый/белый кор...