Votes - 4, Average rating: 3.8
(
)
)
|
manual abstract
Power Saving If the load is left at stable status, ("STB" as shown in Figure 4) for longer than 15 minutes, the screen will flash "–" to save power and will return to normal weighing readings when the load is changed. If the load is left at stable status for over 60 minutes, the scale will turn OFF automatically. -6-Model T10006 50 Kg Digital Crane Scale Overload Warning Remote Control If the load exceeds the maximum capacity Functions (net + tare weight), -OL- will be displayed on the screen. DO NOT overload the scale. Failure to stay below the maximum load rating may result in injury, damage the scale, and void your warranty. Turning the Scale OFF To turn the scale OFF, hold down the button on the scale or hold down the OFF button on the remote control. Note: The scale will not turn off unless it is at the main weighing screen. Figure 5. Remote control buttons. .................................................. Zero Tare Display LED MR M+ F1 Clear Off Hold ........... Do not use this scale during lighting and rain storms or other inclement weather. Turn the scale off, unplug any charging equipment and remove the battery. ........... If this scale is used for the selling of goods, it must be "Legal for Trade" and calibrated regularly. Lb/Kg Conversion The crane scale can display either in pounds or kilograms. To change between the measures of weight, press MR button on the remote and the screen will display SHIFT. Press HOLD and the screen will display UN=0 if converting to kilograms, or UN=1 if converting to pounds. If the current weight is in pounds, the "lb" light on the scale will light up. If the current weight is in kilograms then the "lb" light will be off. Model T10006 50 Kg Digital Crane Scale -7 Scale Battery The scale will automatically display the current scale battery voltage when you turn the scale ON and OFF. To check the voltage during use, press the MR button on the remote control and the screen will display SHIFT. Press the F1 button and the screen will display U X.XX. To return to the main display, press MR again. When the battery voltage is lower than U 5.80, the screen will flash to alert you. The scale will continue to display for approximately one minute longer until -Lb- is displayed on the screen, and then turn OFF automatically. The scale will need to be charged before further use. To recharge the battery: 1. Turn the scale OFF. 2. Connect the supplied adapter into the socket located in the back of the scale, then into a grounded 110V outlet. The light turns orange while charging and turns red when charging is complete. Note: The battery should re-charge for at least 8 hours. Hold Function When the load has been added to the scale, wait until the STB light goes off signifying that the load is stable (Figure 4). If you would like the weight value to remain on the screen, press the HOLD button on the remote control. To clear the screen, press the HOLD button again. Current Zero Value: The current zero value is the tare weight that was selected. To view the current zero scale value, press the MR button and the screen will display SHIFT. Press the button on the remote control to display the current zero value. Advance Tare Weight To input a known tare weight before weighing an item, press MR and the screen will display SHIFT. Press TARE, and the screen will display 000.00. To input the desired weight, scroll to the right by pressing the right arrow (TARE) on the remote control until you come to the number that you would like to change. To increase the number from zero, press the left button ( ) on the remote control. To decrease the number, press CLEAR on the remote control. When you are satisfied with the current number, press the M+ to move to the left. To submit the tare amount, press MR and the TARE light will come on the scale, automatically deducting the imputed tare weight. The tare weight will stay the same until the scale is turned OFF. Clear Function To clear, press the CLEAR button and the screen will flash CLr. If you would like to approve the clear command, press MR and the screen will display 888.88, confirming the deletion. If you would like to cancel the clear command, press the CLEAR button again. The screen will display noCLr canceling the deletion. Search Overload Times To review how many instances the scale has been overloaded, press the MR button and the screen will display SHIFT. Press the CLEAR button and the screen will display OL=XX, showing how many times the scale has exceeded its maximum capacity. Display Function To change the brightness of the display, press F1. Display brightness ranges from 1 (minimum light) to 5 (maximum light). The default display setting is 2. -8- Model T10006 50 Kg Digital Crane Scale Display Action Note: The remote control is a generic remote and may contain buttons that will not be used with this particular model. Should you lose the included remote control, these functions can not be completed. To obtain a replacement controller ...