Login:
Votes - , Average rating: ( )

User manual Sub-Zero, model PRO VENTILATION HOODS

Manafacture: Sub-Zero
File size: 267.16 kb
File name: aa21602f-728d-4b43-b92b-7cc4ea9cfcda.pdf

Language of manual:en

The document is loading, please wait
The document is loading, please wait

manual abstract


Once the heat lamp bulb is cool, use a soft cloth to unscrew the bulb and replace. Be sure that the heat lamp bulb is cool before touching. CLEANING AND CARE Most surfaces of your Wolf Pro hood are stainless steel. Although resistant to most stains, it is not totally impervious to damage. GENERAL CLEANING Salt and some cooking liquids may pit and stain the surface. Always remove any film or spills immediately. Avoid using abrasive cleaners. They will permanently scratch the surface. Do not use steel wool pads. Be careful not to soak the rotary switches. Although they are sealed, excessive moisture may cause damage to the controls. Use a clean cloth or sponge, wipe with warm water and mild detergent. Rinse and dry immediately. Apply protective polish, always in the same direction as the grain. A spray degreaser will remove fingerprints and greasy spatters. Spray on a cloth and wipe surface. Buff dry immediately to avoid streaking. Apply a protective polish to the surface to maintain luster and protect against food stains. Use white vinegar and water to remove hard water stains. DECORATIVE RAIL Clean the decorative hood rail using warm soapy water. Then hand dry with a clean, soft cloth. It is not necessary to remove the decorative rail from the hood assembly. It should be cleaned in place. Be careful not to pull or hang on the bar, as this could damage the hood assembly. Dimensions in parentheses are in 12 millimeters unless otherwise specified. WOLF PRO VENTILATION HOOD USE & CARE STAINLESS STEEL FINISH Use a soft, nonabrasive stainless steel cleaner like Signature Polish (see side note on page 12) and apply with a soft lint-free cloth. To bring out the natural luster, lightly wipe the surface with a water-dampened microfiber cloth, followed with a dry microfiber cloth. All work should follow the same grain direction as the finish. Best results are obtained by keeping the cloth in continuous contact with the metal. Under no circumstances should you use a metallic or highly abrasive cleaner or cloth, as this will damage the finish. FILTER CARE The stainless steel baffle filters and grease cups (if applicable) should be cleaned approximately every month, depending on use. You may need to clean the filters more often if your cooking style generates large amounts of grease (for example, frying or wok cooking). The filters are dishwasher safe and are designed to fit most dishwashers. Wolf recommends wiping filters and grease cups to remove any excess grease before placing in the dishwasher. Refer to page 11 for the stainless steel filter removal and reinstallation procedures. TROUBLESHOOTING GUIDE PROBLEM POSSIBLE SOLUTION Motor and lights do not operate A fuse in your home may be blown or the circuit breaker tripped. Replace the fuse or reset the circuit breaker. Electrical connections at the electrical box may be made incorrectly. Contact your installer. Motor runs but lights The bulb may have burned out. will not operate Switch operation may be faulty. Motor does not Check to ensure blower is plugged into function, but lights hood receptacle. are operational Connect motor directly to a supply cord, bypassing hood. If the motor runs, contact a Wolf authorized service center to check switch operation and wiring between hood and blower. Excessive fan speed and/or noise Check to ensure blower wheel is not hitting side of blower. Adjust if necessary. Check blower mounting hardware. Tighten if necessary. Check for obstructions in damper flap and ductwork. Check for excessive length of duct run, number of transitions and elbows, and duct diameter. Low fan speed adjustment may be needed. 13 WOLF SERVICE INFORMATION CONTACT INFORMATION Wolf Customer Service: 800-332-9513 Website: wolfappliance.com SERVICE INFORMATION When requesting information, literature, replacement parts or service, always refer to the model and serial number of your ventilation hood. This information is found on the product rating plate located inside the left wall of the hood shell. Refer to the illustration for your specific model on pages 6–10 for the location of the rating plate. Record the rating plate information below for future reference. Model Number Serial Number Installation Date Wolf Authorized Service Center and Phone Wolf Dealer and Phone PRODUCT REGISTRATION Register your new Wolf product today so that we may ensure your satisfaction. You may register by one of the following options: 1) Mail in the completed Wolf Product Registration Card. 2) Register online at wolfappliance.com. 3) Register by phone by calling the Wolf Customer Service Department at 800-332-9513. The model and serial numbers of your appliance are printed on the enclosed Wolf Product Registration Card. If you provide us with your e-mail address, we will send you exciting new product updates and recipes as they become available, along with information on special events. BEFORE CALLING FOR SERVICE Before calling your Wolf authorized service center, refer to the Troub...

Reviews



Your review
Your name:
Please, enter two numbers from picture:
capcha





Category