Votes - 1, Average rating: 5 ( )

Manafacture: Dacor File size: 592.86 kb File name: 2f60fba8-76b3-1644-fd9e-ad09a7c28bec.pdf Language of manual:

• Similarly, position the lower chimney section and fix the lower part to the frame using the 2 screws 12c (2,9 x 9,5) provided. • When installed in the recirculation mode the ducting outlet extension pieces 14.1 should align with the rectangular holes in each side of the chimney. • Position the recirculation grilles 8a and 8b so the slats face in a forwards and upwards direction. Fitting the Hood Body • Before fixing the hood body to the frame: • Pull the Comfort Panel to open it. • Disconnect the panel from the hood canopy by sliding the fixing pin lever. • Remove the grease filters from the hood body. • Remove any activated charcoal filters. • From below, use the 4 screws 12f (M6 x 10) .......................... ............ Electrical Connections THIS APPLIANCE MUST BE EARTHED Electrical Requirements Any permanent electrical installation must comply with the latest I.E.E. Regulations and local Electricity Board regulations. For your own safety this should be undertaken by a qualified electrician e.g. your local Electricity Board, or a contractor who is on the roll of the National Inspection Council for Electrical Installation Contracting (NICEIC). Electrical Connection Before connecting to the mains supply ensure that the mains voltage corresponds to the voltage on the rating plate inside the cooker hood. • Remove the grease filters (see paragraph Maintenance) being sure that the connector of the feeding cable is correctly inserted in the socket placed on the side of the fan. • Push fit the Cmd connecter on the cable from the motor housing to the one from the control box. • Connect the lights connector Lux. • Place both the Lux and Cmd connectors in the junction box 24 and close it using the two screws 12e (2,9 x 9,5) provided. • Fix the junction box to the hood body using the two screws 12c (2,9 x 6,5) provided. • For the recirculation version, fit the activated charcoal odour filter. • Replace the grease filters. This appliance is fitted with a 3 core mains cable and must be permanently connected to the electricity supply via a double-pole switch having 3mm minimum contact gap on each pole.A Switched Fuse Connection Unit to BS1363 Part 4, fitted with a 3 Amp fuse, is a recommended mains supply connection accessory to ensure compliance with the Safety Requirements applicable to fixed wiring instructions. This appliance conforms to BS 800: 1988 and EEC Directive No. 78 308 regarding suppression of radio and television interference. ............................ Using the cooker hood The cooker hood is designed to extract unpleasant odours from the kitchen, it will not extract steam.The appliance can be installed to recirculate or extract contaminated air. To Operate Select the required fan speed and light if required. Recirculation In the recirculation mode the contaminated air enters the cooker hood through the grease filters.The air is cleaned by passing through the charcoal filters before being passed back into the kitchen through the grilles in either side of the chimney stack. Extraction In the extraction mode the contaminated air enters the cooker hood passing through the grease filters and is passed out through the ducting into the atmosphere. To obtain the best performance when cooking it is advisable to switch the cooker hood on for a few minutes before you start cooking and leave it running for about 15 minutes after finishing. When used in the ducting mode the charcoal filters are not required. Never do flambe cooking under this cooker hood. Never leave frying pans unattended during use, as over-heated fats and oils can catch fire. Do not leave naked flames under the cooker hood. Ensure heating areas on your hob are covered with pots and pans when using the hob and cooker hood simultaneously. Cooker Hood Controls The hood can be switched on by pressing the required speed button without having to select 1 button. . ................... . The functions of touch controls are explained on the next page Touch control Basic functions Indicator lights Dual Function L When briefly pressed it switches the lighting system on and off. Touch control unlit Lights off When pressed for 2 seconds it switches the electroluminescent lighting ...

Download now

Please, enter two numbers from picture: