Votes - 3, Average rating: 4 ( )

Manafacture: Electrolux File size: 1.5 mb File name: 99043841.pdf Language of manual:

- 4 PREPARE THE HOOD Unpack hood and check contents. You should receive: 1 - Hood 1 - Decorative Flue Assembly 1 - Parts Bag containing: 1 - Mounting Bracket 1 - Discharge Collar 1 - Flue Mounting Bracket 8 - Mounting Screws (4.8 x 38mm Pan Head) 4 - Mounting Screws (3.9 x 9.5mm Pan Head) 2 - Mounting Screws (3.9 x 6mm Flat Head) 8 - Drywall Anchors 1 - Installation Instructions MOUNTING BRACKET DISCHARGE COLLAR FLUE MOUNTING BRACKET 8 MOUNTING SCREWS (4.8 x 38mm Pan Head) 8 DRYWALL ANCHORS 4 MOUNTING SCREWS (3.9 x 9.5mm Pan Head) DECORATIVE FLUE 2 MOUNTING BRACKET SCREWS (3.9 x 6mm Flat Head) FIG. 3 PREPARE THE HOOD Unpack hood and check contents. You should receive: 1 - Hood 1 - Decorative Flue Assembly 1 - Parts Bag containing: 1 - Mounting Bracket 1 - Discharge Collar 1 - Flue Mounting Bracket 8 - Mounting Screws (4.8 x 38mm Pan Head) 4 - Mounting Screws (3.9 x 9.5mm Pan Head) 2 - Mounting Screws (3.9 x 6mm Flat Head) 8 - Drywall Anchors 1 - Installation Instructions MOUNTING BRACKET DISCHARGE COLLAR FLUE MOUNTING BRACKET 8 MOUNTING SCREWS (4.8 x 38mm Pan Head) 8 DRYWALL ANCHORS 4 MOUNTING SCREWS (3.9 x 9.5mm Pan Head) DECORATIVE FLUE 2 MOUNTING BRACKET SCREWS (3.9 x 6mm Flat Head) FIG. 3 - 5 INSTALL THE DUCTWORK (DUCTED HOODS ONLY) ! CAUTION: To reduce the risk of fire, use only metal ductwork. 1. Decide where the ductwork will run between the hood and the outside. 2. A straight, short duct run will allow the hood to perform most efficiently. 3. Long duct runs, elbows, and transitions will reduce the performance of the hood. Use as few of them as possible. Larger ducting may be required for best performance with longer duct runs. 4. Install a roof or wall cap. Connect round metal ductwork to cap and work back towards hood location. Use duct tape to seal the joints between ductwork sections. INSTALL ELECTRICAL FIG. 5 8” 4” 12” CABLE FIG. 4 ROOF CAP 6” ROUND DUCT DECORATIVE FLUE HOOD WALL CAP ROUND ELBOW 24” TO 30” ABOVE COOKING SURFACE (see “INSTALL MOUNTING BRACKETS” section for mounting restrictions 6” ADAPTER CEILING WARNING: Electrical wiring must be done by a qualified person(s) in accordance with all applicable codes and standards. This range hood must be properly grounded. Turn off electrical power at service entrance before wiring. (DUCTED AND NON-DUCTED HOODS) 1. Plan where the hood will be located above the cook top. 2. Run electrical cable, 2-wire plus ground, to the hood location as shown. 3. Flues conceal the cable. Make sure cable exits the wall within dimensions shown and long enough to reach the hood. Fig. 5. 39” INSTALL MOUNTING BRACKET (DUCTED AND NON-DUCTED HOODS) 1. Construct wood wall framing that is flush with interior surface of wall studs. Make sure: a) the framing is centered over installation location. b) the height of the framing will allow the mounting bracket to be secured to the framing within the dimensions shown. 2. After wall surface is finished, secure mounting bracket to framing using dimensions shown. FRAMING BEHIND WOOD CROSS SUPPORT FIG. 6 DRYWALL WOOD CROSS SUPPORT CEILING HEIGHT 8-FOOT 8-FOOT HOOD DISTANCE ABOVE 36” HIGH COOK TOP (see note a) 24” 25” 26” 27” 28” 29” 30” MOUNTING BRACKET LOCATION ABOVE 36” HIGH COOK TOP 39” 40” 41” 42” 43” 44” 9-FOOT 40” 41” 42” 40” 41” 42” 43” 44” 45” DUCTED NON-DUCTED DUCTED OR NON-DUCTED DUCT METHOD 39” 10-FOOT (see note b) DUCTED 39” 40” 41” 42” 43” 44” 45” Note a - Minimum hood distance above cook top must not be less than 24”. A maximum 30” above cook top is highly recommended for best capture of cooking impurities. Distances over 30” are at the installers discretion;...

Download now

Please, enter two numbers from picture: