Votes - 2, Average rating: 4
(
)
)
|
manual abstract
Flashing touch control Charcoal odour filter saturaion alarm.Charcoal filter has to be replaced and metal grease filters washed.The alarm starts up after 200 working hours.(Activation; check the paragraph "Odour filter") 6 OPERATING INSTRUCTIONS OPERATING INSTRUCTIONS To Operate Select the required fan speed and light if required. Recirculation In the recirculation mode the contaminated air enters the cooker hood through the grease filters. The air is cleaned by passing through the charcoal filters before being passed back into the kitchen through the grilles in either side of the chimney stack. Extraction In the extraction mode the contaminated air enters the cooker hood passing through the grease filters and is passed out through the ducting into the atmosphere. To obtain the best performance when cooking it is advisable to switch the cooker hood on for a few minutes before you start cooking and leave it running for about 15 minutes after finishing. When used in the ducting mode the charcoal filters are not required. Never do flambe cooking under this cooker hood. Never leave frying pans unattended during use, as over-heated fats and oils can catch fire. Do not leave naked flames under the cooker hood. Ensure heating areas on your hob are covered with pots and pans when using the hob and cooker hood simultaneously. MAINTENANCE AND CLEANING Before carrying out any maintenance or cleaning isolate the cooker hood from the mains supply. The cooker hood must be kept clean, as a build up of grease or fat can be a fire hazard. External Cleaning Wipe the cooker hood frequently with warm soapy water using a mild detergent. Never use scouring pads or abrasive cleaners. Never use excessive amounts of water when cleaning particularly around the control panel. Metal Grease Filters The filters are washable and must be cleaned when the F-Touch control lights up or at least every 2 months of operation, or more frequently for particularly heavy usage. Remove the metal grease fi lters one at a time by: Releasing the catches on the filters, the filters can be removed. The metal grease filters should be washed, by hand, in mild soapy water or in a dishwasher. Allow to dry completely before replacing. Alarm signal reset Stop the motor. Press the F-Touch control for at least 4 seconds until the T1-Touch control fl ashes. 7 Before carrying out any maintenance or cleaning isolate the cooker hood from the mains supply. MAINTENANCE AND CLEANING MAINTENANCE AND CLEANING Charcoal Filters In the recirculation mode the charcoal filters absorb smells and unwanted odours. Enabling the alarm signal • In Recirculation Version Hoods, the Filter saturation Alarm must be enabled at the time of installation or later. • Switch off the lights and the motor. • Disconnect the mains power supply to the hood by removing the motor unit power supply cable connector, switching off the power supply at the Mains or turning the Main switch off. • Restore the connection, pressing and holding T2. • Release the touch control, touch controls L, T2 and F will light up normally. • Within 3 seconds press the touch control F until the key itself flashes to confirm as follows: • 2 flashes – Charcoal odour Filter saturation Alarm ENABLED • 1 flash - Charcoal odour Filter saturation Alarm DISABLED This filter cannot be washed or regenerated, and must be replaced when the F touch control starts to flash, or at least once every 4 months. The alarm is only triggered when the motor is on. To Remove/Replace the Charcoal Filters • Remove the metal grease filters • Remove the saturated activated carbon filter by releasing the fixing hooks • Fit the new filter by hooking it into its seating • Replace the metal grease filters. This appliance can be a possible fire hazard if the grease and charcoal filters are not cleaned and replaced as recommended. Alarm signal reset • Stop the motor. • Press the touch control F for at least 4 seconds, until the touch control T1 fl ashes. Changing the Light halogen • Remove the 2 screws fixing the Lighting support, and pull it out of from the Hood. • Extract the lamp from the Support. • Replace with another of the same type, making sure that the two pins are properly inserted in the lamp holder socket holes. • Replace the Support, fixing it in place with the two screws removed as above. 8 SOMETHING NOT WORKING SOMETHING NOT WORKING If, having followed these instructions carefully, your cooker hood fails to work properly please carry out the following checks. Symptom Solution The cooker hood will not start • Check the hood is connected to the electricity supply. • Make sure the switch is in the ‘ON’ position. The cooker hood is not working effectively • The fan speed is set high enough for the task • The grease filter is clean. • The kitchen is adequately vented to allow the entry of fresh air. • If set up for recirculation, check that the charcoal filter is still effective. • If set up for extraction, check that the ducting and outlets are...