Votes - , Average rating:
(
)
)
Manafacture: Best
File size: 1.21 mb
File name: e3686e81-694c-4f0c-8232-d84a5c254846.pdf
Language of manual:
The document is loading, please wait
 |
The document is loading, please wait
manual abstract
O For stubborn cases, use a plastic scouring pad or soft bristle brush together with cleaser and water. Rub lightly in direction of polishing lines or "grain" of the stainless finish. Avoid using too much pressure which may mar the surface. O DO NOT allow deposits to remain for long periods of time. O DO NOT use ordinary steel wool or steel brushes. Small bits of steel may adhere to the surface causing rust. O DO NOT allow salt solutions, disinfectants, bleaches, or cleaning compounds to remain in contact with stainless steel for extended periods. Many of these compounds contain chemicals which may be harmful. Rinse with water after exposure and wipe dry with a clean cloth. Painted surfaces should be cleaned with warm water and mild detergent only. Glass Cleaning Use a soft cloth and a glass cleaning solution only! DO NOT use abrasive cloths, steel wool, or scouring pads. DO NOT use strong cleaning solutions or abrasive powders. - 11 OPERATION LIGHT BLOWER SWITCH SPEED 2 Controls The hood is operated using the (5) push-buttons located at eye-level, on the front edge of the hood. The light switch turns the halogen lights on and off. Push the light switch once to turn the lights ON - push a second time to turn the lights ON to a brighter level - push a third time to turn the lights OFF. BLOWER ON-OFF / SPEED 1 0-1 2 3 4 LED LED LED LED BLOWER SPEED 4 BLOWER SPEED 3 The blower on-off / speed 1 switch turns the blower on to its lowest running speed. To turn OFF the blower, push in and hold this blower switch for approximately 2 seconds. The blower speed 2 switch turns the blower on to medium-low running speed. Pressing this switch a second time sets a timer which keeps the blower operating at this speed for 10 minutes. The LED will blink during this time and the blower will shut off automatically. The blower speed 3 and blower speed 4 switches operate the same as blower speed 2 switch except: Blower speed 3 is medium-high and blower speed 4 is high. After every 30 hours of operation, the LED above the “blower speed 1 switch” will be illuminated (RED) and blink for 30 seconds after turning off the blower. This is a reminder to clean the grease filters. Once the grease filters are cleaned and installed, press in and hold the “light switch” button for approximately 2 seconds during the blink of the LED. HEAT SENTRY™ Your hood is equipped with a HEAT SENTRY™ thermostat. This thermostat is a device that will turn on or speed up the blower if it senses excessive heat above the cooking surface. 1) If blower is OFF - it turns blower ON to HIGH speed. 2) If blower is ON at a lower speed setting - it turns blower up to HIGH speed. When the temperature level drops to normal, the blower will return to its original setting. WARNING The HEAT SENTRY thermostat can start the blower even if the hood is turned OFF. When this occurs, it is impossible to turn the blower OFF with its switch. If you must stop the blower, do it from the main electrical panel. - 12 HALOGEN BULBS This range hood requires four (4) halogen bulbs (max 20W, 12V, TYPE MR16 bulb shielded, GU 5.3 Base). ALWAYS SWITCH OFF THE ELECTRICITY SUPPLY BEFORE CARRYING OUT ANY OPERATIONS ON THE APPLIANCE. To change bulbs: 1. Loosen the ring nut by turning it counterclockwise. 2. Pull the bulb downwards to remove - DO NOT ROTATE. CAUTION: BULB MAY BE HOT! 3. Replace with halogen bulb type max 20W, 12V, MR16 bulb shielded, GU 5.3 Base. IN CASE THE NEW HALOGEN BULB DOES NOT LIGHT UP ONCE IT IS ON, CALL FOR SERVICE. BULB RING NUT FUSE REPLACEMENT SWITCH OFF THE ELECTRICITY SUPPLY. To lift the lower flue. Open the electrical box. Replace with the same type of fuse (5x20mm, 5A, 125V). FUSE ELECTRICAL BOX - 13 WARRANTY BROAN ONE YEAR LIMITED WARRANTY Broan warrants to the original consumer purchaser of its products that such products will be free from defects in materials or workmanship for a period of one year from the date of original purchase. THERE ARE NO OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, IMPLIED WARRANTIES OR MERCHANT ABILITY OR FITNESS FOR A PARTICULAR PURPOSE. During this one-year period, Broan will, at its option, repair or replace, without charge, any product or part which is found to be defective under normal use and service. THIS WARRANTY DOES NOT EXTEND TO FLUORESCENT LAMP STARTERS, TUBES, HALOGEN AND INCANDESCENDT BULBS. This warranty does not cover (a) normal maintenance and service or (b) any products or parts which have been subject to misuse, negligence, accident, improper maintenance or repair (other than by Broan), faulty installation or installation contrary to recommended installation instructions. The duration of any implied warranty is limited to the one-year period as specified for the express warranty. Some states do not allow limitation on how long an implied warranty lasts, so the above limitation may not apply to you. BROAN’S OBLIGATION TO REPAIR OR REPLACE, AT BROAN’S OPTION, SHALL BE THE PURCHASER’S SOLE AND EXC...