Votes - 5, Average rating: 4 ( )

Manafacture: Smeg File size: 322.24 kb File name: Language of manual:

SMEG reserves the right to make changes and corrections to its products as it deems necessary, without altering their basic characteristics. 16 Accesories supplied 1 150/ 120 mm reduction. 1 Anti-recoil valve. 2 Support for tubecover. 4 Wall plugs (O6 x 30). 4 Wall plugs (O8 x 40). 4 Long bolts (O4 x 30). 2 Screws (O3,9 x 19). 6 Long bolts (O5 x 45). 2 O6,4 x O18, washers. 2 Clips. Installation Fig. 1 (Page 39) On installing the kitchen hood make sure that the Safety Instructions set out on page 14 are complied with. To obtain optimum performance, the externalconduct must not be more than FOURMETRES long, have no more than two 90° angles and its diameter must be at least O120. 1) Trace and drill the points for fitting the wallplugs onto the wall (A1) (O8 x 40). See figurenr. 1. 2) Fit the wall plugs (A1) and screw in the longbolts (A2) (O5 x 45) leaving them protruding 5mm out of the wall. 3) Attach the kitchen hood to the long bolts(A2). Straighten the apparatus and tighten the the tubecovers. 9) Fit the clips (F) to the support (C). 10) Centre the support (C) around the shape marked; trace and drill the fixing points for the wall plugs (E) (O6 x 30). Attach the support (C) with the long bolts (D) (O4 x 30). 11) Fit the part (B) if the inner tube (not supplied) is O120. 12) Attach the inner tube with a clamp (not supplied) to (B) or on to the motor's air outlet vent as the case may be. 13) Once the inner tube is fitted, fit the lower tubecover around the extractor fan outlet and attach the upper tubecover with the screws (G) (O3,9 x 19). Active charcoal filters (Optional) When exterior gas extraction is not possible, then the kitchen hood may be set to purify theair by recycling it through active charcoalfilters. The active charcoal filters have an active life of three to six months, depending on the individual conditions of use. These filterscannot be washed nor regenerated. They mustbe replaced once their useful life comes to anend. Fig. 2 (Page 39) 1) Put the filters into the lateral draught section GB of the motor making the holes in the filtersmatch up (A) with the pivots (B) of the motor long bolts. carcass. Turn as indicated in the diagram.4) Trace the location of the wall plugs (R) (O8 2) Remove the tubecovers (E). Fit the diffuser x 40), through the inside of the kitchen hood. (C) on to the motor's air outlet vent. Fit the5) Loosen the long bolts (A2) and take the tubecovers back on (E). kitchen hood off. 6) Drill into the wall and fit the wall plugs (R). 7) Attach the kitchen hood, tighten the longbolts (A2) and (S) (O5 x 45) with the washers (T) (O6,4 x O18). 8) Mount the tubecovers, attaching the lowerone to the support (H) as per the detail in figure 1. Lift the upper tubecover up to the desiredheight and mark its shape on the wall. Remove * Se Informationsbricka inuti flaktkapan. * Zie beschrijving van de eignschappen in het interieur van de afzuigkap. * проверьте табличку характеристик внутри вытяжки * Se Informationsbricka inuti flaktkapan. * Zie beschrijving van de eignschappen in het interieur van de afzuigkap. * проверьте табличку характеристик внутри вытяжки 2121 ...

Download now

Please, enter two numbers from picture: