Votes - 3, Average rating: 4.3 ( )

Manafacture: Emerson File size: 248.25 kb File name: Language of manual:

Check to see that all connections are tight, including ground, and that no bare wire is visible at the wire connectors, except for the ground wire. Do not operate fan until blades are in place. Noise and fan damage could result. WARNING ! 7 EMERSON FAN CONTROL BLACK BLACK FAN WIRE LISTED OUTLET BOX LIGHT CONTROL GREEN WIRE (GROUND) FROM HANGER BRACKET TO 120 VOLT SUPPLY WHITE GROUND GREEN WIRE (GROUND) FROM HANGER BALL GROUND WIRE WHT. BLACK (HOT) BLUE RED GROUND THREE-CONDUCTOR CABLE (WITH GROUND) BETWEEN CEILING AND WALL OUTLET BOXES LISTED WIRE CONNECTOR (4)Figure 10 3. If you are going to use a single wall switch to control your ceiling fan, uplight, and optional Emerson Light Fixture (if installed) simultaneously, you will need a standard two-wire (with ground) conductor cable between the ceiling and wall outlet boxes. The fan speed and uplight can then be operated from the pull chain switches in the switch housing; the optional light fixture can be operated from the light fixture switch. Refer to Figure 11 and proceed as follows: a Connect the green grounding lead from the hanger ball and the green grounding lead from the hanger bracket to the supply grounding conductor (this may be a bare wire or wire with green colored insulation). Securely connect wires with a wire connector (supplied). b. Securely connect the fan motor white wire to the supply white (neutral) wire using a wire connector (supplied). c. Securely connect the fan motor black wire and blue wire to the supply black (hot) wire using a wire connector (supplied). d. After connections have been made, separate the white and green wires from the black and blue wires. e. Carefully turn the wires upward and insert them up through the open side of the hanger bracket and into the outlet box. Push the green and white wires into one side of the outlet box; push the black and blue wires into the other side of the outlet box. WARNING ! Check to see that all connections are tight, including ground, and that no bare wire is visible at the wire connectors, except for the ground wire. Do not operate fan until blades are in place. Noise and fan damage could result. BLACK FAN WIRE LISTED OUTLET BOX GENERAL USE ON/OFF WALL SWITCH GREEN WIRE (GROUND) FROM HANGER BRACKET TO 120 VOLT SUPPLY WHITE GROUND GREEN WIRE (GROUND) FROM HANGER BALL GROUND WIRE WHT. BLACK (HOT) BLUE BLACK GROUND TWO-CONDUCTOR CABLE (WITH GROUND) BETWEEN CEILING AND WALL OUTLET BOXES LISTED WIRE CONNECTOR (3)Figure 11 8 4. Screw the two 1-1/4” threaded studs (supplied) into the tapped holes in the hanger bracket (Figure 9). 5. Lift the ceiling cover up to the threaded studs and turn until the studs protrude through the holes in the ceiling cover (Figure 12). 6. Secure the ceiling cover in place by sliding lockwashers (supplied) over the threaded studs and installing the two knurled knobs (supplied). (Figure 12.) Tighten the knurled knobs securely until the ceiling cover fits snugly against the ceiling. 7. Screw in four T8 25-watt (maximum) candelabra base bulbs (supplied) into the uplight sockets on top of the fan housing assembly. 8. Position the cover plate on the switch housing cover (Figure 13) and secure in place by installing the finial nut finger tight. NOTE: If you are going to install an Emerson accessory light kit, do not install the finial nut and cover plate. Instead, install the switch housing cover on the light kit in accordance with the Emerson light kit Owner’s Manual. To avoid possible fire or shock, make sure that the electrical wires are completely inside the outlet box and not pinched between the ceiling cover and the ceiling. ! WARNING CEILING COVER THREADED KNURLED STUDS (2) KNOB (2) LOCKWASHER (2) Figure 12 SWITCH HOUSING COVER COVER PLATE FINIAL NUT Figure 13 8-32 x 3/8" PAN HEAD SCREWS (3) SWITCH HOUSING COVER Figure 15 9. Position the switch housing cover so that the tab on the inside of the switch housing cover aligns with the notch in the switch housing (Figure 14). With the switch housing cover held in this position, pass the shortest pull chain through the nearest bushing. 10. Attach the smaller pendant to the smallest pull chain using a coupling (Figure 14). Pass the longer pull chain through the other bushing; attach the largest pendant to this pull chain using a coupling. 11. Position the switch housing cover over the switch housing and rotate slightly until the tab in the cover engages with the notch in the switch housing. Install three 8-32 x 3/8” pan head screws to secure the cover in place (Figure 15). SWITCH HOUSING COVER PENDANT COUPLING TAB PENDANT COUPLING VIEW "A" BUSHING SWITCH CHAIN SWITCH HOUSING SEE VIEW NOTCH "A" Figure 14 Using Your Ceiling Fan 1...

Download now

Please, enter two numbers from picture: