|
manual abstract
psig (3.5 kPa). The stove, when installed with a blower, must be electrically connected and grounded in accordance with local codes. In the absence of local codes, use the current CSA C22.1 CANADIAN ELECTRICAL CODE in Canada or the ANSI/NFPA 70-1996 NATIONAL ELECTRICAL CODE in the United States. The blower power cord must be connected into a properly grounded receptacle. The grounding prong must not be removed from the cord plug. GENERAL INFORMATION FOR YOUR SATISFACTION, THIS STOVE HAS BEEN TESTFIRED TO ASSURE ITS OPERATION AND QUALITY! Minimum inlet gas supply pressure is 4.5 inches water column for natural gas and 11 inches water column for propane. Maximum inlet gas pressure is 7 inches water column for natural gas and 13 inches water column for propane. When the valve is set to "HI", the manifold pressure under flow conditions is 3.5 inches water column for natural gas and 10 inches water column for propane. When the fireplace is installed at elevations above 4,500ft, and in the absence of specific recommendations from the local authority having jurisdiction, the certified high altitude input rating shall be reduced at the rate of 4% for each additional 1,000ft. W415-0158 / E / 02.19.04 Change in flame appearance from "HI" to "LO" is more evident in natural gas than in propane. Expansion / contraction noises during heating up and cooling down cycles are normal and to be expected. This appliance is only for use with the type of gas indicated on the rating plate. (See page 14). This appliance is not convertible for use with other gases, unless a certified kit is used. INST INSTINSTINSTINSTINSTALLER: ALLER:ALLER:ALLER:ALLER:ALLER: It ItItItItIt is isisisisis y yyyyyour ourourourourour r rrrrresponsib esponsibesponsibesponsibesponsibesponsiblity litylitylitylitylity to tototototo c ccccchec hechechechecheck kkkkk of ofofofofoff fffff the thethethethethe appropriate appropriateappropriateappropriateappropriateappropriate box boxboxboxboxbox on ononononon the thethethethethe rating ratingratingratingratingrating plate plateplateplateplateplate according accordingaccordingaccordingaccordingaccording to tototototo the thethethethethe model, model,model,model,model,model, venting ventingventingventingventingventing and andandandandand gas gasgasgasgasgas type typetypetypetypetype of ofofofofof the thethethethethe unit. unit.unit.unit.unit.unit. CARE OF GLASS, AND PLATED PARTS Do not use abrasive cleaners to clean these parts. Buff lightly with a clean dry cloth. The glass is 3/16" ceramic glass available from your Napoleon / Wolf Steel Ltd. dealer. DO NOT SUBSTITUTE MATERIALS. Clean the glass after the first 10 hours of operation with a recommended gas fireplace glass cleaner. Thereafter clean as required. DO NOT CLEAN GLASS WHEN HOT! If the glass is not kept clean permanent discolouration and / or blemishes may result. SHIPPING BRACKET To avoid the stove being damaged during shipping, a shipping bracket has been used and must be unbolted before the stove can be installed. 1. Remove the four nuts holding the shipping bracket to the bottom of the stove. 2. Lift the stove up and away from the skid to clear the threaded bolts sticking through the bracket. Set down on a flat surface. The stove top is not secured to the unit. 3. Discard the nuts, bracket and the skid. 4 NUTS SHIPPING BRACKET GS60: Maximum input is 35,000 BTU/hr for natural gas and 31,500 BTU/hr for propane. This stove is approved for bedroom and bed-sitting room installations. GDS60: TOP VENT / REAR VENT VERTICAL TERMINATION: Maximum input is 35,000 BTU/hr for natural gas and 31,500 BTU/hr for propane. Maximum output for natural gas is 27,300 BTU/hr at an efficiency of 78%. Maximum output for propane is 24,570 BTU/hr at an efficiency of 78%. Maximum A.F.U.E. (annual fuel utilization efficiency) rating is 72% for natural gas and 71% for propane. REAR VENT HORIZONTAL TERMINA- TION: Maximum input is 21,000 BTU/hr for natural and propane gas. This application requires changing the main burner orifice. This stove is not approved for closet or recessed installations. It is approved for bathroom, bedroom and bedsitting room installations. This stove may be installed in an aftermarket permanently located, manufactured (mobile) home, where not prohibited by local codes. FIGURE 1 LOCATION & CLEARANCES LOCATION & CLEARANCES Provide adequate ventilation and combustion air. Provide adequate accessibility clearance for servicing and operating the stove. Never obstruct the front opening of the stove. GDS60 AND GS60 As long as clearance to combustibles is kept within the required distances, the most desirable and beneficial location for a Napoleon stove is in the centre of a building, thereby allowing the most efficient use of the heat created. The location of windows, doors and the traffic flow in the room where the stove is to be located should be considered. If possible, you should choose a location where the vent will pass through the house without cutting a fl...
Other models in this manual:Fans - GDS60-P (6.21 mb)
Fans - GS60-N (6.21 mb)
Fans - GS60-P (6.21 mb)