|
manual abstract
2. Align the flat sides on the spigot with the recesses in the top of the casing. Insert and snap fix the spigot into the casing. 3. Connect the 100mm (4 ins) ducting to the spigot and make an air tight seal. 4. Remove the charcoal filters. Recirculation The cooker hood is supplied specified for use in the recirculation mode with the charcoal filter/s fitted. In the recirculation mode contaminated air is passed through the charcoal filter/s to be purified and recirculated into the kitchen through the outlet on the top of the cooker hood. 13 Fitting the Cooker Hood to the Wall 1. Fit the brackets with the round ends facing downwards. 2. Once the brackets are secured, lift the hood squarely to the wall slightly higher than the brackets and lower the cooker hood until it is located onto the two brackets. Ensure that the cooker hood is correctly located before letting go. 3. By loosening the screws in the extension arm the hood can be aligned with the front of the adjoining wall cabinets. 4. The hood should be secured on each side to the adjoining wall cabinets using the 4 x 15mm (1/2 ins) security screws provided. 5. Adjust the lower spacer panel at the rear of the hood to close the gap to the wall. Decor Panel The dimensions of the door panel should be 596mm (23 1/2 ins) wide by 350mm (13 3/4 ins) in height. Fitting a Decor Panel to the Hood Visor 1. Remove the complete visor assembly by first pulling the visor open while simultaneously pressing down on the release catch located behind the visor on the left hand side of the casing. 2. Using the paper template provided, mark the screw hole positions on the reverse side of the decor panel. Ensure that the paper template is aligned with the top edge of the decor panel. Failure to align the top edge of the decor panel with the template will prevent the visor from opening when installed. 3. Before drilling, use a tape measure to check the distances of the screw holes (as given on the template). The template may have altered due to dampness after manufacture. 4. Use the 6 x 15mm (1/2 ins) round headed screws provided to attach the decor panel to the hood visor. 14 To Refit the Hood with Decor Panel Attached 1. Insert the upper visor guides into the upper track in the front of the casing. 2. Pull down the bottom edge of the visor and insert the lower guides into the track in the bottom of the casing. 3. Push the visor in until an audible click is heard. 4. The visor can now be opened and closed in its normal function. Adjustment If a heavy door is fitted or if the visor will not stay closed it may be necessary to make an adjustment to the closing mechanism of the visor. Insert a small flat bladed screw driver through the hole (the friction assembly) on either side of the casing indicated by the letter “V” and turn clockwise to apply pressure on the guide. Both friction assemblies should be adjusted by the same amount to ensure the visor opens smoothly. Care should be taken when removing the visor with the decor panel for cleaning or servicing, as the visor is now extremely heavy and should it be dropped, it could damage the appliance beneath and adjoining work surfaces. 15 . ! /. . . . . . . 2 . 3. 4"'. ./ /. . 4 / . / . / . $'1 . 6'1 . . . . 7' . 8'& +. 1 . . // '. '& . . . . . . . . . . . . . . . . . . . . . . . . !" . #$$. & '()(*(*(+,. . . Please refer to your guarantee card for the guarantee conditions. Replacement cards are available on request from the above address. 16 17 18 19 55 - 77 High Street - Slough BERKSHIRE SL1 1DZ © Electrolux plc 2002 ...
Other models in this manual:Fans - MCH 662 (360.97 kb)
Fans - MCH 662 (360.97 kb)
Fans - MCH 662 (360.97 kb)
Fans - MCH 662 (360.97 kb)