Login:
Votes - 1, Average rating: 4 ( )

User manual Air King, model MCH 660

Manafacture: Air King
File size: 692.4 kb
File name: 68618f00-e047-47ff-b830-204caad4c9fd.pdf
Language of manual:en
Free link for this manual available at the bottom of the page



manual abstract


A minimum clearance height of 685mm (27”) is required when installed above a slot-in electric oven, or 787mm (30 1/2 ”) when installed above a slot-in gas oven. When installed between adjoining wall cabinets, the wall cabinets must not overhang the hob and the distance between the underside of the cabinet and the worktop must be 450mm. If the height of the wall cabinet is less than 450mm a gap of 50mm must be maintained either side of the hob. This cooker hood must not be installed above a cooking appliance with a high level grill. Unpacking The fittings supplied to install this cooker hood can be found with the instruction book inside the packaging and consists of the following: Wall/suspended fixing template Plastic rawl plugs (2) Fixing screws (4) Wall Fitting The cooker hood is fitted to the wall using the keyhole slots in the back of the hood. 1. Mark the position on the wall for the two O 8mm dia screw holes (A) as illustrated in the drawing opposite at 568mm. 2. Check that the hole distances are correct and are level using a spirit level. 3. At this stage it is important to allow 25mm (1”) clear space above the cooker hood to enable it to be hooked onto the screws and for subsequent removal for decorating or servicing. 4. Insert the screws and tighten to a distance of 5mm. Hob A: Built-in Electric Hob: 650mm minimum clearance B: Built-in Gas hob: 700mm minimum clearance C: Slot-in Electric Cooker: 685mm minimum clearance D: Slot-in Gas Cooker: 787mm minimum clearance 12 Venting The hood is more effective when used in the extraction setting (ducted to the outside). Venting kits may be purchased through your retailer or DIY store, and must be ducted to an outside vent of 100mm (4”) minimum. The ducting used must be manufactured from fire retardant material which should conform to the relevant British Standard or DIN4102-B1. When the hood is ducted externally the charcoal filter must be removed and the slider control must be in the ducting position. To Fit the Ducting 1. Fit the ducting spigot and blanking plate, by aligning the interlocking lugs on the fittings, with the recesses in the aperture as illustrated in (A) and (B) opposite. 2. Insert and turn anti-clockwise to lock the spigot and blanking plate into position. Recirculation The charcoal filter must be fitted for recirculation and the slider control must be in the recirculation position. Fitting the Cooker Hood to the Wall 1. Remove the grille by pressing inwardly on the two slide catches. 2. Hinge the grille forward to free it from the guides in the side of the casing. The two keyhole slots are now visible. 3. Hook the hood onto the screws using the keyhole slots. 4. Tighten the screws to secure the hood to the wall. Ensure the cooker hood is correctly located before letting go. 5. Refit the grille onto the cooker hood -insert the left hand hinge pin into the hole in the left hand side of the casing. -slide the right hand hinge pin into the guide over the stop position. -close the grille and secure using the two slide catch bolts. 13 14 15 55 - 77 High Street - Slough BERKSHIRE SL1 1DZ © Electrolux Household Appliances Limited 2001 ...

Other models in this manual:
Fans - MCH 660 (692.4 kb)
Fans - MCH 660 (692.4 kb)
Fans - MCH 660 (692.4 kb)
Fans - MCH 660 (692.4 kb)

Reviews



Your review
Your name:
Please, enter two numbers from picture:
capcha





Category