Votes - 2, Average rating: 4 ( )

Manafacture: Kobe Range Hoods File size: 1.92 mb File name: manaul-CH-27-SQ-EN-FR-SP-091207.pdf Language of manual:

Access the wire connections underneath the hood by removing the bottom casing from the six screws. Before reattaching the bottom casing, make sure wires do not slip between motors, impellers, or any moving parts to prevent any damage. -Connect three wires (black, white and green) to house wires and cap with wire connectors. -Connect according to color: black to black, white to white, and green to green. -Test the operation of the hood before moving on to the next step. Make sure power is supplied to the hood. Final Assembly 1. Turn power ON in control panel. Check all lights and fan operation. 2. Make sure to leave this manual for the homeowner. 17 OPERATING INSTRUCTIONS This KOBE hood is equipped with four electronic controls with a 10-second standby startup & 30-second delay shutoff, two powerful centrifugal turbine impellers with safety screens, two bright 12-volt 20-watt halogen lights, and four oil containers or baffle filters. The four electronic controls are Light Control, Speed Control A (cycles through Low, Medium, High, QuietMode), Speed Control B (cycles through Low, QuietMode, High, Medium) and the Power Control (On/Off). Refer to Figure 30. Figure 30 Speed Control A (Cycles through Low, Medium, High, Qi M d ) Power Control Speed Control B (Cycles through Low, QuietMode, High, Medium) Light Control Turn On: -Press Power Control (On/Off) button once. (If any Control button is not pressed within 10 seconds, power will be automatically turned off). -The KOBE hood will start on Low speed. Each press of the Speed Control button will cycle through the various speeds. -Press Speed Control A button to cycle from Low, Medium, High, or QuietMode. Press Speed Control B button to cycle from Low, QuietMode, High or Medium. -Press Light Control button to turn halogen light on. Turn Off: -Press Power Control (On/Off) button once, panel lights will flash and power will be completely shut off after 30 seconds. OR -Press Power Control (On/Off) button twice, all power will be shut off immediately. -If only the lights are on, pressing Power Control (On/Off) button once will turn power off after 30 seconds. 18 MAINTENANCE SAFETY WARNING NEVER PUT YOUR HAND INTO AREA HOUSING THE FAN WHILE THE FAN IS OPERATING. Cleaning Hood Surface CAUTION: NEVER USE ABRASIVE CLEANERS, PADS, OR CLOTHS. DO NOT USE PAPER TOWEL ON STAINLESS STEEL. For optimal operation, clean range hood and all baffle/spacer/filter/oil tunnel/oil container regularly. *** Regular care will help preserve the appearance of the hood. 1. Use only mild soap or detergent solutions. Dry surfaces using soft cloth. DO NOT USE PAPER TOWELS. 2. If hood looks splotchy (stainless steel hood), use a stainless steel cleaner to clean the surface of the hood. Avoid getting cleaning solution onto or into the control panel. Follow directions of the stainless steel cleaner. Caution: Do not leave on too long as this may cause damage to hood finish. Use soft towel to wipe off the cleaning solution, gently rub off any stubborn spots. Use dry soft towel to dry the hood. 3. DO NOT allow deposits to accumulate or remain on the hood. 4. DO NOT use ordinary steel wool or steel brushes. Small bits of steel may adhere to the surface and cause rusting. 5. DO NOT allow salt solutions, disinfectants, bleaches, or cleaning compounds to remain in contact with stainless steel for extended periods. Many of these compounds contain chemicals, which may be harmful. Rinse with water after exposure and wipe dry with a clean lint free cloth. To Clean Safety Screens and Impellers CAUTION: DRAIN OIL CONTAINER BEFORE OIL CAN OVERFLOW. 1) Normal Cleaning -Spray a mild degreaser into the fan and turn on high speed. Liquid residue will accumulate in the oil containers. 2) Cleaning Safety Screens -Remove the safety screen screw and slide the safety screen out. -Wash with warm soapy water. Dry completely before returning into place. -Top rack dishwasher safe. To Clean Baffle Filter CAUTION: DRAIN OIL FROM BAFFLE FILTER BEFORE OIL WILL OVERFLOW. 1. Remove all the baffle filters and oil tunnel. 2. Using a sponge, wash with warm soapy water. Dry completely before returning into place. (Note: Baffle Filters are top rack dishwasher safe.) 19 Replacing Light Bulb CAUTION: HALOGEN LIGHT UNIT MAY BE HOT! WAIT UNTIL UNIT IS COOL. • • • 1. Make sure all controls are off, and range hood is unplugged. 2. Place the flat-headed screwdriver into the groove of the halogen light glass covering and the housing. • 3. Pop out the halogen light glass covering. • 4. Gently pull out the defective light bulb and discard. Light bulbs should be 12V 20W maximum. • 5. Using a cloth, hold the new light bulb and push securely into light socket. 6. Return halogen light glass cover to the housing. • 7. Turn range hood ON to test for operation. 20 SPECIFICATIONS MODEL / SIZE CH2730SQB / 30" CH2736SQB / 36" CH2742SQB / 42" CH2748SQB / 48" COLOR Commercial Grade Stainless Steel CONSUMPTION / AMPERE CH2730SQB – 232W / 2.21A CH2736SQB – 232...

Download now

Please, enter two numbers from picture: