Order the wall or roof cap and any transition needed in advance. Wall Framing for Adequate Support • These vent hoods are heavy. Adequate structural support must be provided. Hoods must be secured to vertical studs in the wall. • It is strongly recommended that the vent hood with duct cover be on site before final framing and wall finishing. This will also help to accurately locate the ductwork and electrical service. Decorative Duct Covers: Decorative duct covers, 6" and 12" high, are available to fit all models. The duct cover conceals the ductwork running from the top of the hood to the ceiling or soffit. Stack one or more duct covers over the top of the hood to reach your ceiling height. Optional Duct Cover Accessories 6" Duct Cover 12" Duct Cover Decorative duct covers are available in 6" and 12" heights. Duct covers may be stacked, in various combinations, to conceal the ductwork running from the top of the hood to the ceiling. • Before you begin, you should determine the installation height of the hood and order the correct size duct cover. The duct covers should be ordered at the same time as the vent hood and be on site before installation. Order the duct cover corresponding to your model. Specification Revised 3/03 POWER SUPPLY IMPORTANT – (Please read carefully) WARNING: FOR PERSONAL SAFETY, THIS APPLIANCE MUST BE PROPERLY GROUNDED. Remove house fuse or open circuit breaker before beginning installation. Do not use an extension cord or adapter plug with this appliance. Follow national electrical codes or prevailing local codes and ordinances. Electric supply These vent hoods must be supplied with 120V, 60Hz, and connected to an individual, properly grounded branch circuit, and protected by a 15 or 20 amp circuit breaker or time delay fuse. • Wiring must be 2 wire with ground. • If the electrical supply does not meet the above requirements, call a licensed electrician before proceeding. • Route house wiring as close to the installation location as possible on the back wall or ceiling. • Connect the wiring to the house wiring in accordance with local codes. Grounding instructions The grounding conductor must be connected to a ground metal, permanent wiring system, or an equipment-grounded terminal or lead on the hood. WARNING: The improper connection of the equipment-grounding conductor can result in a risk of electric shock. Check with a qualified electrician or service representative if you are in doubt whether the appliance is properly grounded. 6" Duct Covers Hood Model 6" Duct Cover Dimensions ZV48T, ZV48S ZV36T, ZV36S ZV30T, ZV30S ZX48DC6 ZX36DC6 ZX36DC6 6"H x 19-11/16"W x 11-7/8"D 6"H x 15-3/4"W x 11-7/8"D 6"H x 15-3/4"W x 11-7/8"D 12" Duct Covers Hood Model 12" Duct Cover Dimensions ZV48T, ZV48S ZV36T, ZV36S ZV30T, ZV30S ZX48DC12 ZX36DC12 ZX36DC12 12"H x 19-11/16"W x 11-7/8"D 12"H x 15-3/4"W x 11-7/8"D 12"H x 15-3/4"W x 11-7/8"D R For answers to your Monogram,® GE Profile™ or Listed by GE appliance questions, visit our website at Underwriters GEAppliances.com or call Laboratories GE Answer Center® service, 800.626.2000. ZV30TSFSS – GE Monogram 30" Stainless Steel Professional Hood Using Duct Cover Accessories To avoid unsightly gaps, plan the hood installation height for duct covers We recommend that the vent hood and decorative duct cover (if used) use. Use the following formula to calculate the need for one of more be on site before final framing and wall finishing. This will help to duct covers and to ensure a trouble free installation. accurately locate studs, ductwork and electrical service. • Read these examples carefully to determine the need for one or more Ceiling Height 6" or 12" duct covers. A - B = C A C B 18" Hood Height A = Countertop to ceiling height. B = Gap at the top of the hood to the ceiling. C = Hood installation height – Plus 18" hood height. NOTE: Dia. C should be between 48" and 54" (for a 30" to 36" installation height). Raise or lower the hood installation height to allow use of one or more 6" and 12" duct covers. INSTALLATION EXAMPLES 8 ft. Ceiling 12" 30" 9 ft. Ceiling 30" 10 ft. Ceiling 36" 24" 30" 8 ft. ceilings: When the hood is installed 30" 9 ft. ceilings: When the hood is installed 30" 10 ft. ceilings: When the hood is installed 36" above the cooking surface and there is no above the cooking surface, order two 12" duct above the cooking surface, order three 12" and soffit or upper cabinetry, order one 12" duct cover accessories. one 6" duct cover accessories. cover accessory. R For answers to your Monogram,® GE Profile™ or Listed by GE appliance questions, visit our website at Underwriters GEAppliances.com or call Laboratories GE Answer Center® service, 800.626.2000. Specification Revised 3/03 ZV30TSFSS – GE Monogram 30" Stainless Steel Professional Hood Features and Benefits • 640 CFM Vertical Exhaust •Variable Speed Fan Control •2 Halogen Lamps with 4 Lighting Levels • Infrared Warming Lamp • Utensil Rod • Removable Grease Trays • Removable Baffle Stainl...