Votes - 1, Average rating: 3
(
)
)
|
manual abstract
ATTENTION! TEMPLATE AND FIXING TO WALL UNIT The lower and back edge of the template must correspond to the lower edge of the wall unit. ATTENTION! TEMPLATE AND FIXING TO WALL The lower edge of the template must correspond to the lower edge of the hood. Only for models with fixing hooks: make the holes and fix two hooks with screws and dowels (J - fig. 4.2). Install the two supplied Y brackets with two screws and washer each onto the upper side of the hood (fig.4.2). 4. Insert the body of the hood inside the wall unit (fig. S). This can remain temporarily in position: a) in case of fixing to the wall unit, using lateral springs D to imbed into the 0 Smm dead holes (to do this, press the lateral springs towards the inside of the body of the hood using a screwdriver as a liver. b) in case of fixing to the wall, with the hooks and the brackets (the bracket have adjustable positioning screws). ATTENTION! Check that the electric cable and the smoke outlet are accessible to facilitate successive connections (and for technical assistance and maintenance interventions). 5. Check that guides G (fig. 6) are perfectly parallel to the lower edge of the wall unit, after which, ONLY in the case of fixing to the wall unit, definitely fix the body of the hood to the sides of the wall unit with 4 screws (E - fig. 6 -two per side). The screws are to be inserted from inside the body of the hood on the wall unit in correspondence with the 4 0 2mm blind holes previously made (see operation 3). 6. Insert the cooker hood cabinet base on the bracket guides G then carry out the electrical connections of the cooker hood cabinet base to the casing (fig. 7). 7. Regulate the cooker hood cabinet base in order that the frontal part is in line with the cabinet (H - fig. 8) then block the cooker hood cabinet base using 2 screws (one per side ■ L - fig. 8 - To insert these two screws you will need to remove the filter grill and screw them on the inserts that are fixed on the mantel guides). 8. Fix the cooker hood cabinet base to the cabinet using the 2 screws M (fig. 8), use 2 of 4 perforations available and check that the screws are fixed to the cabinet. 9. Remount the grease filter, connect the cooker hood to the electrical network and to the discharge tube, check the perfect operation of the cooker hood. INSTRUCTION ON MOUNTING AND USE GB INSTRUCTION ON MOUNTING AND USE II Electrical connection The electrical tension must correspond to the tension noted on the label placed inside the cooker hood. Connect the electrical plug, where provided, to the an easily accessible outlet in conformity with local standards in force. Where an electrical plug is not provided (for direct connection to electrical network) place a standards approved bipolar switch with an aperture distance of not less than 3mm (accessible) from the contacts. Operation - Model with electronic controls If the hood fails to operate correctly, briefly disconnect it from the mains power supply for almost S sec. by pulling out the plug. Then plug it in again and try once more before contacting the Technical Assistance Service. Warning! Always press the fan off button A before disconnecting the hood from the mains supply. Operation - Model with button panel A ■ Lighting, on/off. B - Fan off (Stand by) C - Timer for selected speed (visualizes the speed selected and flashing LED on the lower side of the display). This knob permits the operation of the cooker hood for a established period: 20 minutes if the speed selected is I 1S minutes if the speed selected is 2 10 minutes if the speed selected is 3 S minutes if the intensive speed P is selected. D - Display showing fan speed (1-3-P), change grease filters (grease filter saturation indicator - F) and change activated carbon filters (carbon filter saturation indicator - C). When the led in the lower right side is on, it indicates that the cooker hood is ready for operation (“standby’ position), the flashing LED indicates that the timer has been activated for selected speed. Warning! The active carbon filter saturation function is not activated. In order to activate the carbon filter saturation indicator, press buttons E and F simultaneously for 3 seconds. Initially, only letter F will fbe displayed, then after the 3 seconds have passed, letter C will be displayed as well, indicating that the carbon filter saturation control system is active. To switch off the system, re-press the same two buttons: letter C appear on display and after 3 seconds letter it disappear and the device will be switched off. E - Knob to decrease the speed: from intensive speed P to speed level I. F - Knob to increase (standby) speed to intensive speed P. Attention! Intensive speed P has a duration of S minutes after which the cooker hood automatically sets the speed to level 2 (suction power). A. on/off light switch B. on/off aspiration switch and minimum power selection B+C. medium power selection aspiration switch...