Votes - 3, Average rating: 4.7
(
)
)
|
manual abstract
If you do not understand the information in this manual, or you have a question about your Incite computer that this manual does not cover, consult your Trek dealer. If you have a question or problem that your Trek dealer can’t handle, contact us at: Trek Bicycle Corporation Attn: Customer Service 801 W. Madison Street Waterloo, Wisconsin 53594 trekbikes.com (920) 478-4670 CONTENTS Safety and general guidelines............................... i Functions.............................................................. 1 Installation ........................................................ 2-3 Setting the computer ........................................ 4-7 6i, 8i ................................................................ 4-5 9i, 11i .............................................................. 6-7 Changing functions and other normal use.......... 8 Replacing the battery........................................... 8 Troubleshooting and Warranty............................ 9 SAFETY AND GENERAL GUIDELINES While riding your bicycle, do not stare at the computer for long periods of time (Figure 1). If you do not watch the road, you could hit an obstacle, which may cause you to lose control and fall. Make sure the computer wire cannot contact the tire or wheel spokes. The wire could be damaged causing the computer to malfunction. Also, the wire could get caught, causing you to lose control and fall. © Copyright Trek Bicycle Corporation 2004 All rights reserved Figure 1- Watch the road when riding. Figure 2- Keep the wire out of the spokes FUNCTIONS Not all Trek Incite computer models have all these functions. Table 1- Function abbreviations, names and explanations FunctionExplanationSpeed Current speed of the bicycle displayed in miles per hour (MPH) or kilometers per hour (KPH). Highest readings: • 6i, 8i: 107.3mph or 172.7kph • 9i, 11i: 80.5mph or 129.6kph CLK Clock Time of day displayed in hours and minutes, in 12-hour or 24-hour format TME Time Amount of time elapsed since last reset. Displayed in hours, minutes, and seconds. Highest readings: • 6i, 8i: 9:59:59 • 9i, 11i: 23:59:59 MAX Maximum speed Highest speed since last Reset displayed to tenths. Highest readings: • 6i, 8i: 107.3mph or 172.7kph • 9i, 11i: 80.5mph or 129.6kph TRP Trip distance Amount of distance elapsed since last Reset displayed in miles or kilometers, and tenths. Highest reading: • 999.9 ODO Odometer Amount of distance elapsed since installation or programming displayed in miles or kilometers. Highest reading: • 99,999 AVG Average speed Average speed since last Reset displayed to tenths. Highest readings: • 6i, 8i: 99.9mph or 172.7kph • 9i, 11i: 80.5mph or 129.6kph CAD Cadence Number of revolutions per minute of the crankset displayed in whole number. Maximum 240. Temperature Current temperature displayed in Fahrenheit or Celsius in whole numbers, updated every 30 seconds. Range: • -2 to 140°F +/-2° • -19 to 60°C +/-1° Pacer Indication whether current speed is above or below average speed displayed by arrow pointing up (above) or down (below). Wheel select Second wheel size calculation, indicated by circle or circle within a partial second circle. Functions INSTALLATION Tools needed: • Electrical tape • Slot-type screwdriver • Phillips-type screwdriver • Scissors This section explains the steps to install your computer onto your bicycle: • Placing the computer on the handlebar • Placing the magnet and sensor(s) on the bike Placing the computer on the handlebar The Trek Incite computer can be mounted on the handlebar or on the stem (Figure 3). To install the computer on the handlebar 1. Determine your bicycle’s handlebar diameter: 22.2mm, 25.4/26.0mm, or 31.8mm. 2. Select the corresponding bar clamp For a 22.2mm bar, use the rubber shim (provided) inside the smaller clamp. 3. Insert the handlebar clamp into the back of the computer base (Figure 4) and slide it towards the front of the base. 4. Insert the rubber friction pad into the computer base, aligned across the computer base. 5. With the wire pointing toward the front of the bike, wrap the bar clamp around the handlebar. 6. Insert the screw through the washer and into the computer base. 7. Tighten the screw until the computer base cannot rotate on the handlebar. 8. Slide the computer into the computer base until the front of the computer and computer base line up. 9. Check that the computer base cannot be rotated around the handlebar, and that the computer cannot slide backwards on the computer base (Figure 5). To install the computer on the stem 1. Insert the rubber friction pad into the computer base, aligned along the computer base. 2. Insert two nylon ties through the computer base (Figure 6). 3. Place the base on the stem and tighten the nylon tie. 4. Slide the computer into the computer base until the front of the computer and computer base line up. 5. Check that the computer base cannot be rotated around the stem and the computer cannot slide backwards on the com...
Other models in this manual:Bikes - Incite 6i, 8i, 9i, 11i (366.34 kb)