Votes - 4, Average rating: 4.5
(
)
)
|
manual abstract
1 Set The Tire Circumference Set the tire circumference in mm. Note Refer to the chart shown on the right. Setting is fixed and completed by pushing the SET button. 3 Increase the number Max. 2999 mm Decrease the number Min. 10 mm MODE Button START/STOP Button SET Button Contact Point Measurement Selection Select the measurement unit, kilometer or mile, by pushing the MODE button. Fix it by pushing the SET button. 2 Kilometer Mile AC Button You need to know your tire size or the roll out length of your tire in MM's. Refer to the chart below for approximate tire lengths. Tire size Tire size is usually shown on the sidewall of tires. Basic Functions Test Spin the rear wheel to see if Speed is reading properly. Push the mode button until Cadence (Cdc) is in the sub-display. Spin the crank arm backwards to test if Cadence is reading properly. When you receive a signal, tightly secure the sensor so it does not move. Note When the computer does not indicate the speed/cadence, check the position of the magnet and the sensor. Mount The Bracket Secure the cord by fastening it to the frame with zip ties at regular intervals. Put the rubber pad 8 on the bracket 1 and secure the bracket on the handle bar with the screw. Slide the computer into the bracket until you hear the click sound. When you need to remove the computer, press the lever on the handlebar bracket and slide the computer forward. Note Allow enough wire clearance in the area marked with to insure you can turn the handlebars all the way from side to side without pulling the wire. 4 3 Rotate the rear wheel. Rotate the crank arm AC Button Preparation Complete. (the screen will show the time measurement in this state) * The auto mode is ON in this state. ® ASTRALE8 Installation of the Computer on Your Bike The computer comes with the following parts: 1 Bracket 2 Cord 3 Speed Sensor (Long Cord) 4 Cadence Sensor (Short Cord) 5 Sensor Rubber Pad 6 Wheel Magnet 7 Cadence Magnet 8 Bracket Rubber Pad 9 Nylon Ties (10) 1 Please read these instructions carefully before installing or using the CAT EYE ASTRALE 8. Please keep this manual in a safe place for future reference. CAT EYE ASTRALE 8 CYCLOCOMPUTER CC-CD200N E: Owner’s Manual Rear wheel spoke Left chainstay The smooth edge of the zip tie should be on the outside Mount the wheel magnet and speed sensor • Mount the wheel magnet 6 on a spoke of the rear wheel so the surface of the magnet faces the sensor. • Mount the speed sensor 3 (long cord) on the left chainstay with nylon ties 9. Note The nylon ties can only be used once, please install with care. U.S. Pat. Nos.4633216/4642606/5226340/5236759 Pat. and Design Pat. Pending Copyright © 2002/2003 CAT EYE Co. Ltd. CCMCD2N-030531 066600252 1 Warning • Pay attention to the road or trail! Do not be distracted by the computer. • Be sure to securely mount the magnet, the sensor, and the bracket on your bicycle. Periodically check to insure they are mounted securely and the screws have not come loose. • Keep batteries out of reach of small children. Dispose of batteries according to local regulations. • Avoid unnecessary prolonged exposure to the sun. • Never attempt to disassemble the computer head. • Don’t use thinner, benzene or alcohol to wipe the surface of the computer. They may damage the surface of computer. Important Note Important Note Mount the magnets 6 and the sensors 3 in the appropriate positions so that the center of each magnet 6 aligns with the marked sensor line when the rear wheel and crank arm are rotated. The magnet should be no more than 5mm from the sensor. Center Marked Line Left chainstay 2 Left Chain Stay Inward Side of The Crank Arm Left Chain Stay Mount the cadence magnet and cadence sensor. • Mount the cadence magnet 7 on the left crank arm so that it faces the sensor. • Secure the cadence sensor 4 (short cord) on the left chain stay with nylon ties 9. Sensor Side Important Note When the crank is spinning, the center of the magnet 7 should pass in front of the sensor 4 marking line. The distance between the sensor and the magnet 7 should be within 5mm. After adjusting the magnet and sensor, secure tightly with nylon ties. Crank Arm Center Marked Line Within 5 mm Rear wheel spoke Adjust Adjust Within 5 mm Sensor Side Lever Slide Power-Saving Screen (When no signal is received for about 1 hr. the screen switches to the power-saving mode) When you push either of the MODE button or the START/STOP button or you ride the bicycle, the display comes back to the measurement display. START/STOP MODE SET SET Speed 0.0 (4.0) - 300.0 km/h [0.0 (3.0) - 185 mph] or Cadence 0.0 (20.0) - 299.9 rpm You can program the tire size. Return to the Elapsed Time Range of set: 10 - 2999 mm Increase the number Decrease the number Display for Measurements Mode Selection Illustrations (bottom of the screen) Cdc Cadence 0(20) - 299 rpm or Speed 0.0 (4.0) - 300.0 km/h Av Average Speed 0.0 - 300 km/h [0.0 - 185.0 mph] Odo Odometer 0.0 - 99999 km [mile] Mx Maximum speed 0.0...