Votes - 1, Average rating: 4 ( )

Manafacture: Star Trac File size: 1.48 mb File name: Language of manual:

Position the handlebar on top of the handlebar post and secure in place using a tension handle and washer. NOTE: Tighten the tension handles firmly. 6. Install the Water Bottle Holders Using the Allen Wrench, remove the two screws from the right side fork of the frame assembly. Position a water bottle holder in place against the frame assembly, and re-install the two screws to secure. Repeat to install the left-side water bottle holder. Step 5 Step 6 You have now completed the assembly of your STAR TRAC V-BIKE® SPINNER®. Page 7 STAR TRAC GROUP CYCLES OWNER’S GUIDE SPINNER® PRO / ELITE / NXT ASSEMBLY AND SETUP Use the following procedures to unpack and assemble your STAR TRAC SPINNER ®. UNPACKING Prepare the area that you will be unpacking and assembling the bike to be free from debris that may cause damage. Observe all safety precautions and care while unpacking and assembling the bike. Position the shipping carton so the “Heavy End” logo is located at the bottom. Open the top of the carton and fold back all four flaps. Carefully tilt the box forward so that the box may be lifted to expose the cycle. Remove all parts from the shipping carton and foam inserts, and verify that the following parts are included in your shipment: Assembly Parts (Spinner Pro shown) Spare Parts Kit NXT Parts List (not shown) Description Qty. Description Qty. Main Frame Assembly 1 Rear Leg Assembly 1 Handlebar Post 1 M10x1.5, 55mm Button Head Screw 4 Handlebar w/ Grip & Water Bottle Holders 1 M10x1.5, 65mm Button Head Screw 4 M8x1.25, 16mm Flat Head Screw 2 M10x1.5 Nyloc Hex Nut 8 M8x1.25, 16mm Socket Set Screw 1 10mm Washer, Flat 16 Seat Post 1 Wrench Hex, 5mm 1 Seat Slider Assembly w/ Saddle 1 Wrench Hex, 4mm 1 Pedals (set of two) 1 Multi Wrench 1 Front Leg Assembly w/ Transport Wheels 1 Spare Parts Kit (includes brake pad and pedal straps) 1 Pro/Elite Parts List (Pro shown above) Description Main Frame Assembly (not shown) Handlebar w/ Grip (& Water Bottle Holders – Elite only) (not shown) A. Seat Slider Assembly, w/ Saddle B. Seat Post C. Rear Leg Assembly D. Front Leg Assembly w/ Transport Wheels E. Pedals (set of two) Qty. 1 1 1 1 1 1 1 Description F. Water Bottle Cages G. Pop-Pins (pre-installed) G. M10x1.5, 55mm Flat Head Screw G. M10x1.5 Nut G. 10mm Washer, Flat G. Wrench Hex, 5mm G. Wrench Hex, 4mm G. Multi Wrench H. Spare Parts Kit (includes brake pad and pedal straps) Qty. 2 3 4 4 4 1 1 1 1 Spare Parts Kit- Save the box of spare parts in a safe place so you have service parts when needed in the future. Page 8 STAR TRAC GROUP CYCLES OWNER’S GUIDE Take time now to enter your V-bike® Spinner® serial number in the space below (serial number is located on the bottom cross member). If parts are missing, or if you have any operational questions, please call Star Trac’s Service department at (800) 5031221; have your serial number ready. Serial No._____________________________________________ NOTE: If you are missing any of the parts listed above, inspect the packing material and the box for items that may have been overlooked. If parts are missing, or if you have any product questions, please call Star Trac’s Service Department at (800) 503-1221, please have your Spinners serial number ready. CAUTION: Damage to the bike during assembly is not covered as part of the limited Star Trac warranty. Take care not to drop or lean the bike on the handle bar pop-pin. Carefully stand the bike up in the normal upright position on a stable surface so it will not tip over during assembly. Page 9 STAR TRAC GROUP CYCLES OWNER’S GUIDE ASSEMBLY Following these steps in order will minimize the build time and ensure proper assembly. Note: Not all of the following procedures are performed on all models; Spinner ® Pro, Elite and NXT. If the procedure is specific to a model it will be noted as follows: NXT Only, Pro/Elite Only, NXT/Elite Only, or Pro Only. 1. Install the Back Leg NXT Only Lift up the rear of the bike frame and place the rear leg assembly in position under the frame, aligning the holes in the leg with the holes in the frame. Position the leg so the thicker end faces toward the front of the bike Using the 5mm hex wrench and a 13mm combination wrench insert 2- M10X55mm (rear-most holes) and 2-M10X65mm (front-most holes) button head screws, nuts Step 1 (NXT) and washers (under bolt head and nut), to secure the rear leg assembly to the frame. Tighten all hardware securely using a torque wrench to 85 Inch Pounds Pro & Elite Only Lift up the rear of the bike frame and place the rear leg assembly in position under the frame, aligning the holes in the leg with the holes in the frame. Using the 5mm hex wrench and a 13mm combination wrench insert 2- M10X55mm flat head screws, nuts and washers to secure the rear leg assembly to the frame Tighten all screws/nuts securely using a torque wrench to 85 Inch Pounds Step 1 (Pro/Elite) 2. Install the Front Leg NOTE: The front foot assembly has wheels attached to the front edge. Be sure the wheels face f...

Download now

Please, enter two numbers from picture: