Votes - 4, Average rating: 3.8 ( )

Manafacture: Cateye File size: 330.95 kb File name: VL510-810_ENG_v3.pdf Language of manual:

Pat. Nos. 4642606, 5236759 and Pat. Pending Copyright©2007 CATEYE Co., Ltd. CCVL51/81-070105 066600560 3 INSTALLING THE UNIT 2 3 6 3 6 5 3 4 1 2 3 3 4 3 SET (on Back) F VELO 5 VELO 8 MODE G 4 YES! 5 NO! 1 Click 1 5 6 7 SETTING 5 5 mm A Before using the computer, please thoroughly read this manual and keep it for future reference. Caution • Do not concentrate on the computer operations while riding. Always be sure to ride safety. • Be sure to securely mount the magnet, sensor and bracket on your bicycle, and periodically check to see if any parts have loosened. • Used batteries are harmful if swallowed by mistake. They must be disposed in accordance with local regulations. • Do not leave the main unit exposed to direct sunlight. Never disassemble the main unit. • For cleaning of the main unit or accessories, use diluted neutral detergent on a soft cloth, and then wipe it off with a dry cloth. Do not use paint thinner, benzine or alcohol since such chemicals may damage the surface. Package Contents 1 Bracket 2 Wire 3 Sensor 4 Magnet 5 Nylon Ties (x 7) IMPORTANT! Correct positions of the sensor and the magnet: A When rotating the front wheel, the magnet's 4 center must be aligned with the sensor's 3 marking line. B The distance between the sensor 3 and the magnet 4 must be less than 5 mm. Name of Parts Speed 0.0 (4.0) to 299.9 km/h [0.0 (3.0) to 185.0 mph] Mode Symbol Indicates the mode currently selected. (The corresponding value is indicated on the lower line.) Pace Arrow* Indicates if the current speed is faster or slower than the average speed. ( Faster Slower) Speed Scale Sub Display (selected function) Battery Case Cover Contact *The Pace Arrow feature is only available on the VELO8. Pace Arrows are not displayed on the VELO5. Display function • Tm* [Elapsed Time] 0:00'00" to 9:59'59" • Dst [Trip Distance] 0.00 to 999.99 km [mile] • Av* [Average Speed] 0.0 to 299.9 km/h [0.0 to 185.0 mph] (Measurable up to 27 hrs or 999.99 km/h) • Mx [Maximum Speed] 0.0 (4.0) to 299.9 km/h [0.0(3.0) to 185.0 mph] • Cal* [Calorie Consumption] 0.0 to 9999.9 kcal (estimated from speed data) • Odo [Total Distance] 0.0 to 9999.9 km [mile] • [Clock] 0:00' to 23:59' [1:00'to 12:59'] * This feature is only available on the VELO8. No measurement is done on the VELO5. Start/Stop of Measuring The unit starts measuring automatically when you start pedaling, and stops measuring when your come to a stop. The upper display always shows the Current Speed. Shift of Lower Display Each time you press the MODE button, a different data value appears on the lower line. e Power Saving Function If the main unit does not receive a signal after about 10 minutes, the main unit enters Power Saving Mode and displays the clock count only. To re turn to normal display, press the MODE button or start your bicycle again to cancel the Power Saving function. Data Reset When a screen with the Reset mark in the OPERATION FLOW is displayed, continue pressing the MODE button and the measured data will return to zero. However, the Odometer (total distance) and Clock do not return to zero. How to Set Clock In the clock mode, press SET button on the back, and the display enters clock setting mode. *If Km/h has been selected for speed scale, it becomes 24-hour clock. If mph has been selected, it becomes 12-hour clock. f How to Change Tire Size Display the Total Distance (Odo) and press the SET button to change the tire size. You can select a tire size in two ways: Either select from among preset sizes c or enter the tire’s circumference directly in increments of 1 cm. d Maintenance • If the contact of the unit or the bracket gets wet, dry it off with a cloth. If they become rusty, it will cause speed detection error. • If the gaps between the buttons and the unit get clogged with mud or sand, wash them away with water. Troubleshooting No display. Has the battery in the main unit run down? Replace it with a new one. The main unit may still have a charge. Put the battery in backwards to short the unit then install properly and do all clear operation. Incorrect data appears. Do all clear operation. Current speed does not appear. (First, short-circuit the contact of the main unit a few times with a piece of metal. If current speed appears, the main unit is working fine and the cause should be attributed to the bracket or the sensor.) Is the clearance between the sensor and the magnet too large? Are the magnet's center and the sensor's marking line aligned? Re-adjust the position...

Download now

Please, enter two numbers from picture: