Login:
Votes - 1, Average rating: 5 ( )

User manual Humminbird, model 900

Manafacture: Humminbird
File size: 581.9 kb
File name: IDMK_900_Install.pdf
Language of manual:en
Free link for this manual available at the bottom of the page



manual abstract


Contact our Customer Resource Center at 1-800-633-1468 or visit our web site at Installation Overview Following are instructions for the installation of this accessory. Before you start the installation, we encourage you to read these instructions carefully in order to get the full benefit from your Humminbird® accessory. If you find that any items are missing from your installation kit, call our Customer Resource Center at 1-800-633-1468 or visit our web site at In addition to the hardware supplied with your In-Dash Mounting Kit, you will need a reciprocating saw for cutting the dash material and masking tape to hold the mounting template in place. Installation Start by placing the components on the surfaces where you intend to install them before installation. Make sure that the surfaces you have chosen provide adequate protection from wave shock, and that all cables can reach the control head. NOTE: If a cable is too short for your application, extension cables are available. Call the Humminbird® Customer Resource Center at 1-800-633-1468 for more information. 1. Locate a suitable, flat area of the dash to mount the control head. The control head requires a depth of at least 3 1/2 inches. 2. Tape the paper In-Dash Mounting template to the desired in-dash mounting location. 3. At a location inside the dotted line on the template, drill a hole large enough to insert blade of reciprocating saw. Carefully begin cutting toward the dotted line, then follow the dotted line around the template. Remove the template when finished. 531589-1_C © 2009 Humminbird®, Eufaula AL, USA. All rights reserved. FoamPadsThreadedInsertWingNutThreadedRoduseforfutureaccessoriesWashersCutAwayDashIn-DashBracketFoamPadsThreadedInsertWingNutThreadedRoduseforfutureaccessoriesWashersCutAwayDashIn-DashBracket 900 Series™ In-Dash Mounting Kit 4. Insert and tighten the two threaded rods into the two threaded inserts located on the back side of the control head. Peel off the adhesive-backed foam pads and place them on the back of the control head; make sure you notice the difference between the longer top/bottom and shorter side pads. Expansion ports - 5. Insert the control head through the mounting hole from the front side of the dash. From the back side of the dash, align the two threaded rods on the rear of the housing with the two holes on the in-dash mounting bracket. Place a washer onto each threaded rod, then secure bracket by placing a wing nut onto each threaded rod and tighten fully. 6. Insert cable connectors into the proper recesses on the cable collector insert. The cable connectors are keyed to prevent reverse installation, so be careful not to force the connectors into the wrong slots. If you don’t have a cable for every hole in the insert, install the blank plugs to protect the unit from the weather. 7. While holding cables in place in the cable collector insert, thread the cables through the slot in the bottom of the cable collector cover, line up the cable collector insert and cover, then slide the cover into place on the insert. NOTE: The tab on the cable collector insert goes into the slot on the cover. 8. Attach the cable collector insert to the cable collector cover using the 2 Phillips screws provided. 9. Plug the cable collector assembly into the back of the control head. Cable connectors and cable sockets are keyed to prevent reverse installation, so be careful not to force the connectors into the wrong sockets. Once the cable collector and all cables are plugged into the back of the control head, lock the assembly into place by threading the knurled screw into the threaded insert on the back of the housing. (Cable ties are provided to help you secure the cables in place by threading them through the available holes on the in-dash bracket). NOTE: It is very important that the cable collector is used and secured in place in the In-Dash installation. Plug Cable Connector Assembly to Back of Control Head KnurledScrew 2 531589-1_C Power Communications Temp/Speed Transducer CableCollectorInsert CableCollectorInsertScrewsTabonInsertSlotonCoverCableCollectorCover © 2009 Humminbird®, Eufaula AL, USA. All rights reserved. 900 Series™ In-Dash Mounting Kit 1-Year Limited Warranty We warrant the original retail purchaser that products made by Humminbird® have been manufactured free from defects in materials and workmanship. This warranty is effective for one year from the date of original retail purchase. Humminbird® products found to be defective and covered by this warranty will be replaced or repaired free of charge at Humminbird® option and returned to the customer freight prepaid. Humminbird® sole responsibility under this warranty is limited to the repair or replacement of a product that has been deemed defective by Humminbird®. Humminbird® is not responsible for charges connected with the removal of such product or reinstallation of replaced or repaired parts. This warranty does no...


Reviews



Your review
Your name:
Please, enter two numbers from picture:
capcha





Category