Votes - 2, Average rating: 3
(
)
)
|
manual abstract
Do not install incompatible forks or suspension parts. An improperly modified frame, fork, or component, can cause you to lose control and fall. ! Caution: Any modification of your frame, fork, or components means that your bike no longer meets our specifications and therefore voids your warranty. SEAT POST SETUP SEATPOST MINIMUM EXTENSION: All Specialized full suspension models with interrupted seat tubes have a small hole to identify the minimum extension allowed for your seatpost. If you cannot see the seatpost tube through this hole, your seatpost is too far extended. If a greater saddle height is required, replace the seatpost with a longer one. .................................................................. BIG HIT FSR FRAME FEATURES 1. Main Frame 2. Seatstay 3. Chainstay 4. Shock Link 5. Main Pivot 6. Dropout (Horst) Pivot 7. Shock Link at Seatstay Pivot 8. Shock Link at Frame Pivot 9. Lower Shock Eyelet 10. Upper Shock Eyelet 11. Shock 12. Replaceable Derailleur Hanger .............................. BIG HIT FSR FRAME GEOMETRY Small (mm) 578 776 128 68.2. 66.3. 63.1. 61. 387 362 1130 432 Large (in) 24.13” 30.67” 5.51” 68.2. 66.3. 63.1. 61. 15.24” 14.25” 45.83” 17.0” Large (mm) 613 779 140 68.2. 66.3. 63.1. 61. 387 362 1164 432 Small (in) 22.76” 30.55” 5.04” 68.2. 66.3. 63.1. 61. 15.24” 14.25” 44.49” 17.0” Medium (mm) 597 777 137 68.2. 66.3. 63.1. 61. 387 362 1148 432 Medium (in) 23.50” 30.59” 5.39” 68.2. 66.3. 63.1. 61. 15.24” 14.25” 45.2” 17.0” *Top Tube Length **Standover Height Head Tube Length Head Tube Angle (26” Steep) Head Tube Angle (26” Slack) Seat Tube Angle (26” Steep) Seat Tube Angle (26” Slack) BB Height (26” High) BB Height (26” Low) Wheelbase Chainstay Length 1 2 3 4 4 5 5 6 6 7 8 * TT length is the Horizontal Measurement from the center-line of the HT at the top of the HT to the center-line of the projected seat tube. ** Stand Over height is measured vertically at the centerpoint of the TT measurement. FRAME SPECIFICATIONS Headset: 1 1/8” Seatpost diameter: 30.9mm Front derailleur clamp: E-Type Rear hub spacing: 135mm (6mm offset) BB shell: 73mm Seat Collar: 34.9mm Stroke (Big Hit Expert): 69.85mm (2.75”) Stroke (Big Hit Comp): 63.5mm (2.5”) Eye-To-Eye: 222.25mm (8.75”) CAUTION! Do not use the link position A in conjunction with the middle frame hole when using a Manitou SPV shock with piggyback reservoir. This may result in shock damage. NOTE: The spring weights listed above are to be used as an adjustment starting point only. Stock springs are set for the long travel setting (lower shock eye bolt) and the middle progression setting (upper shock eye bolt). Positioning the shock in the shorter travel setting and/or the higher/lower progression settings may require that the spring be changed accordingly. Refer to your shock manufacturer’s manual for additional shock setup information. Larger impacts require a higher spring weight and a lower sag setting to prevent bottoming out. Be sure to adjust or replace the spring accordingly. RIDER WEIGHT <150lb 150-185lb 185-220lb SPRING RATE 350lb 400lb 450lb BIG HIT FSR FRAME GEOMETRY 51386274 NOTE: Bearing and Bolt Kits are available only through your local Specialized dealer. To retain your warranty and for your safety, all maintenance should be performed by your local Specialized dealer. Bearing Kit Parts Bolt Kit Parts SBC LIMITED WARRANTY Specialized Bicycle Components, Inc. (“Specialized”), a California corporation located at 15130 Concord Circle, Morgan Hill, California 95037, makes the following Limited Warranty concerning Specialized bicycles and framesets: LIMITED LIFETIME WARRANTY ON BICYCLE FRAMES AND FRAMESETS Subject to the following limitations, terms and conditions, Specialized warrants to the original owner for the lifetime of the original owner of each new Specialized bicycle or frameset that the bicycle frame or frameset when new is free of defective materials and workmanship. The lifetime limited warranty is conditioned upon the bicycle being operated under normal conditions and use, and properly maintained. This limited warranty does not apply to paint/finish or components attached to the bicycle/frameset such as front forks, wheels, drive train, brakes, seatpost, handlebar and stem or any suspension related parts or components. Paint/finish, components attached to the bicycle/ frameset such as front forks, wheels, drive train, brakes, seatpost, handlebar and stem or any suspension related parts or components are covered under the limited one (1) year warranty. This warranty is void if the bicycle or frameset was not purchased new from or not properly assembled by an authorized Specialized dealer. LIMITED ONE (1) YEAR WARRANTY ON COMPLETE BICYCLE Subject to the following limitations, terms and conditions, Specialized warrants to the original owner of each new Specialized bicycle that this bicycle when new is free of defective materials and workmanship. This warranty shall expire one (1) year from the date of the original...