Votes - 1, Average rating: 4
(
)
)
|
Other manuals for this model:
manual abstract
. Only the confirmation signal is switched on. „ Confirmation signal and operation error signal switched on.* ™„ Energy consumption display(Ask your electricity supply company what the mains voltage is) ‹ Consumption display switched off.* ‚ Consumption display with mains voltage at 230 V. . Consumption display with mains voltage at 400 V. „ Consumption display with mains voltage at 220 V. … Consumption display with mains voltage at 240 V. ™† Automatic timer ‹ Switched off.* ‚-SS Cooking time, after which the hotplates switch off ™‡ Duration of the timer end signal ‚ 10 seconds.* . n 30 seconds „ 1 minute. ™S Time for selecting the hotplate ‹ Unlimited: The last selected hotplate can always be adjusted without having to select it again.* ‚ Once you select a hotplate, you have 10 seconds to adjust it, after which you will have to select it again in order to be able to adjust it. ™‹ Reset to basic setting ‹ Switched off.* ‚ Switched on. * Basic setting Changing the basic settings 3. Touch the 0 symbol repeatedly until the desired symbol appears on the left-hand display. The hob must be switched off. 4. Set the desired value on the settings range. 1. Switch on the hob. 2. Within the next 10 seconds, touch the 0 symbol for 4 seconds. 5. Touch the 0 symbol for 4 seconds. The setting is activated. Switching off To exit the basic setting, switch off the hob with the main switch and make new settings. ................ ™ and ‚ flash alternately in the left-hand display and ‹ lights up in the right-hand display. ................ Cleaning and care The information in this section provides help on how best to care for your hob. Suitable maintenance and cleaning products can be purchased from the after-sales service or in our e-Shop. Ceramic Clean the hob after each use. This will prevent spills from burning onto the ceramic. Only clean the hob when it has cooled down sufficiently. Use only cleaning agents which are suitable for glass ceramic. Follow the cleaning instructions on the packaging. Never use: ¦ Undiluted washing-up liquid ¦ Detergent intended for dishwashers ¦ Scouring agents ¦ Harsh cleaning agents such as oven spray or stain remover ¦ Abrasive sponges ¦ High-pressure cleaners or steam jet cleaners Ground-in dirt can be best removed with a glass scraper, available from retailers. Please note the manufacturer's instructions. You can also obtain a suitable glass scraper from our after- sales service or from the e-Shop. Using special sponges to clean glass ceramic achieves great cleaning results. Hob surround To prevent damage to the hob surround, observe the following instructions: ¦ Use only hot soapy water. ¦ Wash new sponge cloths thoroughly before use. ¦ Do not use any sharp or abrasive agents. ¦ Do not use the glass scraper. Rectifying faults Faults often have simple explanations. Please read the notes in In order that the electronics do not overheat, the hotplates are the table before calling the aftersales service. switched off as and when necessary. The ”., ”…, or ”† display appears alternately with the • or oe residual heat The electronics of your hob are underneath the control panel. indicator. For various reasons, the temperature in this area may rise sharply. Display Fault Measure Blank There is no power supply. Check the household fuse for the appliance. Check whether there is a power cut by trying other electronic appliances. All displays flash The touch controls are wet or an object is Dry the touch controls or remove the object. resting on them. ”. Several hotplates have been used over a Wait a while. Touch any touch control. When ”. goes out, the prolonged period at high power settings. electronics have cooled down sufficiently. You can continue To protect the electronics, the hotplate cooking. has been switched off. ”… Despite the switch-off by ”., the elec-Wait a while. Touch any touch control. When ”… goes out, you tronics have become hot again. All hot-can continue cooking. plates have therefore been switched off. ”† and the heat set-Warning: There is a hot pan in the area of Remove the pan. The fault display goes out shortly afterwards. ting flash alternately. the control panel. There is a risk that the You can continue cooking. An audible signal electronics will overheat. can be heard ”† and audible sig-There is a hot pan in the area of the con-Remove the pan. Wait a while. Touch any touch control. When nal trol panel. To protect the electronics, the ”† goes out, you can continue cooking. hotplate has been switched off. ”‰ The hotplate was in operation for too long You can switch the hotplate back on again immediately. and has switched itself off. After-sales service Our after-sales service is there for you if your appliance should need to be repaired. We are committed fo find the best solution also in order to avoid an unnecessary call-out. E number and FD number: Please quote the E number (product number) and the FD number (production number) of your appliance when contacting the after...
Other models in this manual:Cooktops - PKE645F17C/01 (1.45 mb)
Cooktops - PKE645F17E/01 (1.45 mb)