Votes - 2, Average rating: 4
(
)
)
|
manual abstract
Open the cable clamp “D” completely. Check the position of the U bolts on the terminal block “B” (Fig. 7a) according to the diagram in Fig. 7b and Fig. 7c. Insert the feeder cable into the cable clamp “D” and into the cable protector “C”. The supply cable must be of a suitable size for the current requirements of the appliance; see ‘Feeder cable section’ following. Connect the phase and earth cables to terminal “B” according to Figs. 7b and 7c. Pull the feeder cable and block it with the cable clamp “D”. Re-mount shield “A”. Note: the earth conductor must be left about 30 mm longer than the others. Feeder cable section “TYPE H05RR-F” 230V 3 x 2.5 mm2 (**) (**) - Connection with wall box connection. C D A B PE 1 2 345 N (L2)L1 230 V 2 3 4 51 N(L2) PEL1 PE Earth N Neutral L Live Fig. 7a Fig. 7b Green and Yellow (Earth) Black or Blue (Neutral) Red or Brown (Live) Fig. 7c Maintenance instructions Semi-rapid burner J Triple ring wok burner Fig. 8b Replacing the burner injectors J If the injectors are not supplied, contact the Fisher & Paykel Authorised Service Centre. Select the injectors to be replaced according to the ‘Table for the choice of injectors’. To replace the injectors: Remove pan supports and burners from the cooktop. Using a wrench, substitute the nozzle injectors “J” (figs. 8a - 8b - 8c) with those Fig. 8a most suitable for the kind of gas used. The burners are designed so that adjustment of primary air is not required. Dual burner J Injector for inner crown Injectors for outer crowns J Fig. 8c 14 Maintenance instructions Setting the burner minimum Check whether the flame spreads to all burner ports when the burner is lit with the gas tap set to the minimum position. If some ports do not light, increase the minimum gas rate setting. Check whether the burner remains lit even when the gas tap is turned quickly from the maximum to the minimum position. If the burner does not remain lit, increase the minimum gas rate setting. To adjust the minimum gas rate setting: Semi-rapid and triple ring wok burners Light the burner. Set the gas valve to position. Remove the knob. Using a thin screwdriver, pass by the hole of microswitch and turn the screw “F” until adjustment is correct (Fig. 9a). Inside crown of DUAL burner Light the DUAL burner. Set the gas valve to position. Remove the knob. Using a screwdriver, turn the screw “H” until the correct setting is obtained (Fig. 9b). Outside crowns of DUAL burner Light the DUAL burner. Set the gas valve to position. Remove the knob. Using a screwdriver, turn the screw “G” until the correct setting is obtained (Fig. 9b). For G30/G31 gas, tighten the adjustment screws completely. F Fig. 9a G H Fig. 9b Maintenance instructions Table for the choice of the Injectors Cat: II 2H 3+ GBIE BURNERS Nominal Power [kW] Reduced Power [kW] G 30 - 28-30 mbar G 31 - 37 mbar By-pass [1/100 mm] O injector [1/100 mm] G 20 20 mbar By-pass [1/100 mm] O injector [1/100 mm] Semi-rapid 1,75 0,45 32 65 97 (Z) Triple ring wok 3,50 1,50 65 95 135 (T) ble Dual inner crown outer crown 1,00 (*) 4,50 (#) 0,32 (*) 1,90 (#) 27 60 50 (no. 1 central 66 (no. 2 outer) 69 (F1) (no. 1 central 102 (Z) (no. 2 outer) adjusta (*): Power calculated with inner crown operating. (#): Power calculated with inner and outer crowns operating. Lubrication of the gas taps A qualified technician must lubricate the gas taps. Important! All installation, maintenance and conversion of the appliance must be done using original factory parts. The manufacturer declines any liability if these correct parts are not used. 16 Introducing your cooker Thank you for buying a Fisher & Paykel freestanding cooker. Once it is installed and ready to use, you will want to know everything about it to make sure you get excellent results right from the start. This guide introduces you to all its special features. We recommend you read the whole guide before using your new cooker, for both safety and cooking success. For more information, go to Gas cooking hob controls: 1 Front left triple ring wok burner control knob 2 Rear left semi-rapid burner control knob 3 Central left dual burner control knob 4 Central right dual burner control knob 5 Rear right semi-rapid burner control knob 6 Front right triple ring wok burner control knob Left oven controls: 7 Function selector control knob 8 Temperature selector control knob 9 Control buttons 10 Clock display 11 Oven temperature indicator light Right oven controls: 12 Function knob 13 Temperature knob 14 Control buttons 15 Clock display 16 Oven temperature indicator light Warming drawer (left drawer only) controls: 17 Warming drawer control knob 18 Warming drawer on indicator light 7 8 9 1 2 3 4 5 6 11 14 12 13 16 17 18 Fig. 10 Cooker control panel 10 15 Using your cooktop 17 Gas burners The knob controls the flow of gas through the safety tap. = closed valve = maximum aperture or flow = minimum aperture or flow You can choose to cook at any heat between and , but never betwee...