Votes - 0, Average rating: 0
(
)
)
|
manual abstract
Installation Instructions please keep Lutfen saklay.n.z 2 A480 55 5 min.30 min.30min.60 150 3 560 520 490 min. 30 min. 50 1 m min. 60 in0m .3 ±1762 43 4 4 5a 5b 7 mm.6 7 8 8 GBPlease detach and keep GBPlease detach and keep Instructions for the installer All work involved in installation, setting and adaptation to a different gas type must be carried out by authorised personnel from our Service Centre and must comply with current regulations and the conditions laid down by the local gas company. IMPORTANT: Cut the gas and electricity supplies to the appliance before any kind of work is performed. Before connecting the appliance to the supply, check that it is prepared for the type of gas in question. Our hobs leave the factory set for the gas type indicated on the characteristics plate. This appliance must be installed in a place with the proper level of ventilation. The gases produced during combustion must be released to the outside. Check the size of the hob and the size of the opening to be made on the kitchen unit. The panelling on the work surface in the immediate vicinity of the hob must be made of non-flammable material. Both stratified coatings and the adhesive used to fix them in place must be heat resistant. Otherwise, they may be damaged. Electric wiring must not come into contact with hot areas. The mains supply cable must be fixed to the kitchen unit to prevent it from coming into contact with hot parts on the oven or hob. Appliances with electric components must be earthed. Handle the appliance with care throughout the entire installation process. Avoid knocking the appliance. This appliance shall be installed in accordance with the regulations in force and only used in a well ventilated location. Read the instructions before installing or using this appliance. SHOULD THE RELEVANT CONDITIONS NOT BE PROPERLY SATISFIED, THE INSTALLER, AND NOT THE MANUFACTURER, SHALL HELD LIABLE. Installing the hob in the kitchen unit The positioning of a hob in a kitchen unit is Class 3 according to the standard for gas appliances EN 30-1. Fitting measurements 1-Minimum Distances (mm). Cut a hole of the necessary size in the work surface, Fig. 2. If no oven is installed under a gas hob, it is suggested to place a separator of non-flammable material e.g. plywood or metal at a distance of 10 mm from the bottom of the hob to prevent access to the lower part of the hob. If the event that a drawer is located beneath the appliance, please make sure that the drawer contains no heat-sensitive or easily combustible objects, such as spray cans or shoe polish. Use a heat-resistant utility drawer only. If the cooking hob is to be installed above an oven, check that the oven is fitted with power ventilation, and check the dimensions according to the assembly manual. Centre the hob in the hole on the work surface. The wood fibres used in the manufacture of kitchen work surfaces are liable to swell when they come into contact with moisture. You are recommended, therefore, to coat cut edges with a special adhesive to protect them from steam or condensed water which could deposit beneath the work surface on the kitchen unit. The fixtures and the watertight seal (lower edge of the hob) come factory-fitted. Do not under any circumstances remove them. The seal keeps the entire work surface watertight and prevents leakage. Once the hob is fitted you should turn the clip and tighten the screw as shown in Fig. 4. For disassembly, unscrew the clip and proceed in the reverse manner. 2-The end of the input collector on gas hobs comes with a 1/2” threaded L-tube.This caters for: Rigid connection. Connection to a flexible metal tube: If this method is used, avoid both contact between this tube and moving parts on the housing (e.g. drawers) and passing the tube through spaces liable to get blocked. In either of the cases, do not move or twist the L-tube from its factory-set position. If, for some reason, the L-tube should be twisted, it is necessary to make sure that this area is properly sealed. Make sure that all connections performed are free of leakage. The manufacturer does not accept any liability for leakage on connections performed by the installer or if the L-tube is moved or twisted. 3-Check the voltage and total power on the characteristics plate. The appliance must be EARTHED. Make sure that connection has been performed in accordance with legal regulations in force for the country in question and complies fully with the conditions laid down by the local electricity company. In order to meet normal safety standards, the installer must supply an all-pole circuit breaker with a contact aperture of at least 3 mm. This is not necessary when connection is made via a socket, so long as this is accessible to the user. Appliances equipped with plugs should only be connected to sockets which are duly earthed. The appliance is type "Y". This means that the input supply cable cannot be changed by the user. Only the brand's service technic...