Login:
Votes - 3, Average rating: 4 ( )

User manual Garland, model GIWOK 3.5 BI (SH/WO/IN 3500)

Manafacture: Garland
File size: 2.53 mb
File name:
Language of manual:en
Free link for this manual available at the bottom of the page



manual abstract


• In case the system finds an error during initialization, the red LED will illuminate. • Disconnect the induction unit from the main power supply. • Check the CU sensors at the plug by means of the Ohm meter. • Re-start the procedure of initialization. • Disconnect the unit from the main power supply. • Remove the short circuit service plug from both the Poti and LED connections. Initializing The Induction Unit By PC Or Laptop The initialization of the CU (RTCS) sensors (excluding all WOK models), as well as adjustments of the pan detection and power performance, can be performed by means of the hyperterminal program. Please refer to Section 9 “IR Interface” for instructions on how to use the hyperterminal program The following adjustments must be done in the hyperterminal program: 2400bps, 8bit, no parity, 1 stop bit, hardware protocol. IMPORTANT NOTE: When replacing the power board and or induction coil with RTCS sensors, you must reset all parameters. IMPERATIVE! Pay close attention to whether you receive a feedback signal from the PC or Laptop after every change. This will be your signal that the change has been accepted successfully. 12345 Entry to the mode of adjustment (password) ; Initialize Cu sensor (temperature of the coil ca. 25°C/77°F) excluding WOK. N Increase the limit of the mains current (+) n Decrease the limit of the mains current (-) “ Save the limit of the mains (power) current T Increase pan detector (+) t Decrease pan detector (-) = Save pan detector -? Leave the mode of adjustment . State software version Change Of The Parameters 1. Connect the RS232 connection cable to the PC/Laptop and straighten the IR-adapter to the left lower corner of the ceran glass. For counter top cookers, refer to Section (9) figure #3 for correct IR adapter positioning. For all Wok cookers, you will be required to remove the top wok bowl assembly. Place the IR-adapter in the left hand corner directly over the rectangular opening located on the metal sheet with ferrit stripes. Please refer to Section (9) figure #4 for Wok cooker IR adapter positioning. 2. Start HT2400 (see chapter 9) and turn unit on! 3. Input “12345” and the mode of adjustment will now begin. The following message will appear on the monitor: IR= On WELCOME REPAIRMEN 4. Not valid for WOK cookers. The parameters on the CPU can now be changed! The unit temperature and the ambient temperature must amount to 25°C (+/- 4°C) or 77°F (+/- 39°F). Press the key [ ; ]. On the console appears the message “please confirm”. Press the key [ ; ] again. The CU (RTCS) sensor will now be initialized on 25°C (77°F). The following message now appears on the monitor: save CU sensor : 25°C 5. Set the limit of the (mains) power current. (see mains current parameters in this section): N increase the limit of the mains current (+) n decrease the limit of the mains current (-) The following message appears on the monitor: linecurrent limit= ....... 6. Save the limit of the (mains) power current with the ...

Other models in this manual:
Cooktops - GIWOK 3.5 (SH/WO 3500) (2.53 mb)
Cooktops - GIU 1.5 (BH/BA 1500) (2.53 mb)
Cooktops - GIU 1.8 (BH/BA 1800) (2.53 mb)
Cooktops - GIU 2.5 (BH/BA 2500) (2.53 mb)

Reviews



Your review
Your name:
Please, enter two numbers from picture:
capcha





Category