Votes - 3, Average rating: 3.7 ( )

Manafacture: Fisher & Paykel File size: 249.99 kb File name: Language of manual:

Failure to do so may result in death or electrical shock WARNING! Hot Surface Hazard During use, accessible parts of this appliance will become hot enough to cause burns. Avoid body or clothing contact with the ceramic glass until it is cool. Keep children away. Handles of saucepans may be hot to touch. Check saucepan handles do not overhang other elements that are on. Keep handles out of reach of children. Failure to do so may result in serious injury. WARNING! Cut Hazard When the safety cover is retracted, the blade in the scraper is razor-sharp. Use with extreme care and always store safely and out of reach of children. Failure to use caution could result in injury or cuts. Safety and warnings Important safety precautions Operation Household appliances are not intended to be played with by children. Children or persons with a disability that may limit their ability to use the appliance should have a competent person to instruct them in its use. This person should be satisfied that they can use the appliance without danger to themselves or their surroundings. This appliance shall not be used as a space heater, especially if installed in marine craft or caravans. If the power supply cable is damaged, it must only be replaced by an authorised person. This appliance should be connected to a circuit which incorporates an isolating switch providing full disconnection from the power supply. Do not use a steam cleaner to clean your cooktop. Do not stand or place heavy objects on this appliance. Do not use pans with jagged edges or drag pans across the ceramic glass surface as this can scratch the glass. Do not use scourers or any other harsh/abrasive cleaning agents to clean your cooktop, as these can scratch the ceramic glass. 6 Installation instructions Dimensions and clearances Models Product Width (side to side) Product Depth (front to back) Product Height (below benchtop) CT560C 578 mm 511 mm 60 mm CT5602F 578 mm 511 mm 60 mm CT2802 289 mm 511 mm 55 mm (cooktop) 578 mm 511 mm 45 mm CT6551S (controls) 88 mm 511 mm 63 mm CT560C, CT5602F, CT6551S CT2802 Fig. 1 Thermal protection barrier - Dimensions and locations of ventilation holes CT560C, CT5602F, CT6551S CT6551S (CONTROL Cutout for CT6551S only 270 3mm PANEL) (CT2802 25mm 70 3mm COOKTOP) (min) Fig. 2 Cutout dimensions Minimum clearance (below benchtop) CT560C 70 mm CT2802 60 mm CT5602F 70 mm CT6551S 65 mm Installation instructions 7 Installing the control panel (CT6551S models only) 1 Remove the supplied clamps from the cooktop and control panel. 2 Feed the cooktop wiring harness up through the control panel cutout. 3 Remove the control panel cover. 4 Connect the cooktop wiring harness by aligning the numbers/letters on the harness with those on the control panel connector block (see Fig. 3 below). Control panel Important! Leave the plastic wiring card attached for future reference. 5 Clamp the wiring harness. 6 Wire the mains power supply to the control panel and clamp. 7 Replace the control panel cover. 8 Roll the control panel into the cutout. 9 Secure the control panel and the cooktop using the clamps provided (see ‘Clamping down the cooktop’ following). Note: two small clamps are supplied and must be used for clamping down the control panel to the benchtop. These clamps are to be screwed to the sides of the control panel. Three clamps are provided for clamping down the cooktop itself (see ‘Clamping down the cooktop’ following). Clamping down the cooktop Place the cooktop into the cutout and tighten with the supplied clamps. These will cope with bench thickness 20-50 mm. Final checklist TO BE COMPLETED BY THE INSTALLER Is the product earthed? Check that the power supply cable is NOT touching the product. This will ensure that the cable is not damaged by heat from the product. Is the product clamped down securely? Check that all the elements function correctly by switching on all of them and leaving them on for at least one minute. Are all elements glowing? Is the ‘Element On’ indicator light functioning when you turn an element on? Turn all the elements on individually to check. To check that the ‘Surface Hot’ indicator light functions correctly, switch off all the elements. Is the ‘Surface Hot’ indicator light functioning? 54PNEEN32154PNEEN321connector block Plastic wiring card Fig. 3 Using the plastic wiring card to align the numbers/letters on the harness with those on the control panel connector block. Fig. 4 Clamping down the cooktop 8 Introduction About your new cooktop Thank you for buying a Fisher & Paykel ceramic glass cooktop. Once it is installed and ready to use, you will want to know everything about it to make sure you get excellent results right from the start. This guide introduces you to all its special features. We recommend you read the whole guide before u...

Download now

Please, enter two numbers from picture: