Votes - 2, Average rating: 3
(
)
)
|
manual abstract
Check Heavy soiling can be removed with oven cleaner eg Easy Off® Fume Free or Easy Off® Heavy Duty the label on the cleaner before using. Ignition electrodes Toothbrush and rubbing alcohol A dirty or wet electrode will prevent the burner from lighting efficiently. EN 11 Replacing the grates The wok grate goes in the center over the wok burner. The other two grates are interchangeable. Care and cleaning Re-assembling the brass wok burner (some models only) Each part of the brass burner has locating pins to help you to assemble it correctly after cleaning. Incorrect assembly can cause dangerous irregular flames and ignition problems. Refer to this diagram for the correct order of assembly. Note: The brass parts of your wok burner will change color with use. This will have no effect on the performance. Rotate vent ring to align locater pin with hole in burner base. Inner cap Outer cap (small holes) Trim ring Vent ring with locater pins (large holes) Align and insert pin Side view Correct grate orientation Rounded corners 12 Frequently asked questions Q What is the best way to clean stainless steel? A See ‘Care and cleaning’ instructions. Q How do I clean the grates and burners? A Grates can be washed in the dishwasher or alternatively with a cream cleaner and a nylon scourer. Burners are best washed in warm water (see ‘Care and cleaning’ instructions). Q All the burners spark at once when I go to light one, is this ok? A Yes, they are designed to do this. Q Why doesn’t my cooktop light? A Firstly, check it is plugged in and the gas is turned on. Alternatively, the gas igniters may be dirty. These are easily cleaned with a toothbrush and rubbing alcohol. (Also check ‘Troubleshooting’). Q Will the graphics on my cooktop come off? A No, these are etched by laser. Q My burner flames are yellow / slow to start, is something wrong? A Yes, there are a number of factors which could be causing this 1. If you use bottled gas this may indicate you are getting near the end of the bottle. 2. Your cooktop may not be suited to the gas you are using, check with your service person/installer. 3. The gas pressure may not be correct, check with your service person/installer. 4. See ‘Troubleshooting’. Q One of my burners has an uneven flame, what can I do? A Check the burner parts are assembled correctly. Q What size pots should I use? A Generally larger pots are more energy efficient (see ‘Cookware’). Q Do I need special pans for a gas cooktop? A Regular pans are fine. We recommend thick-based pans for efficient, even heat. EN 13 Troubleshooting Problem Possible solutions My cooktop does not light Check it is plugged in and there is power to the wall socket. The gas igniters may be dirty. These can be easily cleaned with a toothbrush and rubbing alcohol. The burner parts may not be located properly. Check the assembly and make sure the burner cap is sitting flat. Check the gas supply valve is turned on and the supply to the house is working. Gas should be heard when you turn a burner on. My burner flames are yellow/slow to start The burner parts may not be located properly. Check the assembly and make sure the burner cap is sitting flat. If you use bottled gas this may indicate you are getting near the end of the bottle. Check that the burner parts are not blocked with water. The gas pressure may not be correct, check with your service person/installer. One of my burners has an uneven flame Check the burner parts are assembled correctly and that the burner cap is sitting flat on the burner. My cooktop is sparking Your cooktop thinks that the flame has gone out. This could be caused by drafts disturbing the flame eg using a down draft. Check that the igniter is clean and dry. Your power supply may not be properly grounded or, in an older house, the correct wiring polarity may not have been observed. The flame goes out at low settings Gas supply pressure may be low, check with service person/ installer. Low setting may be incorrect, check with your service person/ installer. Limited warranty When you purchase any new Fisher & Paykel whiteware Product for personal or consumer use you automatically receive a two year Limited Warranty covering parts and labor for servicing within the 48 mainland United States, Hawaii, Washington D.C and Canada. In Alaska the Limited Warranty is the same except that you must pay to ship the Product to the service shop or the service technician’s travel to your home. Products for use in Canada must be purchased through the Canadian distribution channel to ensure regulatory compliance. If the Product is installed in a motor vehicle, boat or similar mobile facility, you receive the same two year Limited Warranty, but you must bring the vehicle, boat or mobile facility containing the Product to the service shop at your expense or pay the service technician’s travel to the location of the Product. EN Fisher & Paykel undertakes to: Repair without cost to the owner either for material or labor any part of t...
Other models in this manual:Cooktops - GC913 (1.15 mb)