Votes - 3, Average rating: 3.7
(
)
)
|
manual abstract
Clamps are provided to fasten the hob to worktops measuring from 20 to 40 mm in thickness. To fasten the hob securely, it is recommended that all the clamps be used. 555 mm 55 mm 475 mm Fastening Clamps - Assembly Diagram 20 30 Clamp Position for Clamp Position for H=20mm top H=30mm top Front 40 Clamp Position for H=40mm top Back N.B: Use the clamps contained in the "accessory kit." d) In case a wooden panel should be fitted under the top for insulation, it will have be fitted at a minimum distance of 20 mm from the inferior part of the top. Important: When installing the hob on a built-in oven, the oven should be placed on two wooden strips; in the case of a joining cabinet surface, remember to leave a space of at least 45 x 560 mm at the back. When installing on a built-in oven without forced ventilation, ensure that there are air inlets and outlets for ventilating the interior of the cabinet adequately. Assembly examples are given in figs. 560 mm. 45 mm. Electrical Connection Electrical Connection THIS APPLIANCE MUST BE EARTHED. The installation procedure must be carried out by a qualified electrician. The electrical safety of this appliance is guaranteed only if the appliance is correctly earthed in compliance with the standards of electrical safety. The manufacturer can under no circumstances be considered responsible for any damage that might occur due to incorrect earthing of the hob. The electric hob is not supplied with a power supply cord because the type of cord used depends on the type of electrical connection (see following diagram). Open the terminal box, following the instructions illustrated in the diagram below: 2 1 1 2 3 4 5 V IMPORTANT POINTS: Your hob is supplied with a special connection cable. If ever the cable is damaged it should be replaced by an authorised service engineer only. Disconnect the hob form the electrical supply before any work is carried out. Electrical Connections: 123 4 5 ••• • • • L N Voltage and frequency of power supply: 230-240V 50-60Hz 7000W Connecting the supply cord to the electrical mains: The hob must be connected to the mains by a double pole mains switch, which must have a minimum 0f 3mm space between the contacts, correctly fused with a capacity appropriate to that shown on the hob Rating Plate. All electrical wiring from the consumer unit to the appliance, via the switched double pole cooker outlet, must be of an acceptable type and current rating as above. The supply cord should conform to BS6004 conductor size 4mm2, must be positioned so that no part of it reaches a temperature of 50°C above room temperature. The electrical installation must comply with the IEE Regulations, Building Regulation & local By-Laws. Before making the connection, make sure that: • the limiter switch (fuse) and the residual wiring can support the appliance load (see the rating plate). • the mains system is properly earthed in compliance with current regulations and provisions. • there is easy access to the socket or the double pole switch after the appliance is installed. IMPORTANT: If the hob is installed above a built-in oven, the electrical connection for the hob must be independent of that for the oven, both for safety reasons and to facilitate the removal of the oven for maintenance, repair etc. Supply cable installation The electric hobs are supplied without a cable. Use a cable: 4mm2 • open the teminal box by removing the "V" screw and taking off the cover. • Fix the cable in place with the "F" cable clamp, close the lid and fasten it with the "V" screw. V 1 2 4 5 F 9 After Sales Service "No company is better positioned to offer an after sales service on a Hotpoint appliance than us - the manufacturer" As part of our commitment to you, all Hotpoint appliances have the added benefit of a fully inclusive parts and labour guarantee for the first 12 months. In addition to this you also have the advantage of free replacement parts for the first 5 years when fitted by a Hotpoint engineer. When the 12 months parts and labour guarantee expires we offer the following after sales service options: Repair Service and Information Help Desk UK: 08709 066066 Republic of Ireland: 1850 302 200 Note: Our operators will require the Model number and the Serial number of your appliance Available 364 days a year with a fast, effective and value for money service. We have the largest white goods repair service in the UK with over 1200 of our own fully trained engineers. All repairs include a parts and labour guarantee for 12 months from the date of the repair. If you require any information or have any questions about your appliance, our operators are on hand with help and advice. All this ensures that you will receive the best available after sales service possible. Extended Warranties UK: 08709 088 088 Republic of Ireland: 1850 502 200 Whether you have just one or a number of Hotpoint appliances in your kitchen, we offer two service cove...