Votes - , Average rating:
(
)
)
Manafacture: Hotpoint
File size: 842 kb
File name: HB6510.pdf
Language of manual:
The document is loading, please wait
 |
The document is loading, please wait
manual abstract
Removable wire shelf hangers. Three wire shelves. Stay Clean side liners. Meat tin with anti-splash tray and fan grilling wire shelf. Removable inner glass door. Reversible Main Oven Door (see opposite). 4 If something goes wrong . First, don’t panic! There may be nothing wrong. Check the points below before calling your Hotpoint Service Office. 1. Check that the mains supply is switched on. 2 Check that the Automatic Cooking Programme has not been selected; if it has switch the oven back to Manual control (see page 10). 3. If using the Grill in the Top Oven make sure that the Top Oven Control is set to ‘O’ Off (see page 7). If it still won’t work... Contact the Service Office If there is still a problem with your Cooker after checking the points above: 1. Switch off the Cooker at the cooker control panel. 2. Call your nearest Hotpoint Service Office or local importer (outside the UK). The telephone number is shown on the back page. Note the number down in the space below: When you contact us we will want to know the following: 1. Your name, address and post code. 2. Your telephone number. 3. Clear and concise details of the fault. 4. The model number (6510) and the colour. 5. The date of purchase. Enter the date here: 6. If you have taken out one of the Hotpoint Service Schemes. Please make sure you have all these details ready when you call. 21 removed with a fine steel wool soap pad. Top Oven/Grill Cleaning Clean grill pan and grid as soon after use as possible to prevent stains being burnt on when the grill pan is used again. Wipe up any spillages as soon as possible to prevent them from being burnt on. Cleaning the Exterior of the Cooker The outside of the cooker should be cleaned regularly to keep it looking like new. Wipe over with a soft cloth wrung out in hot water and dry with a soft clean cloth. Wear protective gloves. You can use mild non abrasive cleaners but always read the manufacturer's instructions first. Always test their suitability on a small area of the cooker not noticeable in normal use. NOTE: DO NOT use scouring pads or abrasive powder which will scratch the glass. 20 Changing the Main Oven door hinging WARNING: Switch off the electricity supply to the cooker at the cooker control unit before changing the door hinging. A pack of fittings is supplied with the information pack in the cooker. This contains: 50 mm double sided tape Door pull sticker Right hand door stay You will need a No.2 Posidriv screwdriver. 1. Open the door fully. Place padding under the door to support the door during the removal of the hinges. 2. Remove the door stay, which Is the small metal bracket adjacent to the hinge, which prevents the oven door opening more than 110°. In order to gain access to the screws the appliance will require tilting backwards and be carefully supported. 3. Unscrew screws and remove hinge and hinge shim at positions 1 and 2. Replace hinge at 5 and 6, replace hinge shim at 7 and 8. Note: The screws in the hinges should be removed and replaced one at a time. Only loosely fit screws No.5 and No.6 at this stage, to allow you to slot the door into position. 4. Unscrew and remove hinge and hinge shim at positions 3 and 4. Replace hinge at 7 and 8, replace hinge shim at 5 and 6. Note: Replace steel washer on the lower hinge. Only loosely fit screw No. 7 at the top to allow you to slot the door into position. Retain screw No.8 on one side for use later. 5. Place the door on a flat surface. 6. Remove screws A, B and C and H and I to remove the inner panel from the outer glass and handle. 7. Remove door catch N and O and blanking plate P and Q and replace on opposite sides of the door. A 7 mm spanner may by required. 8. Remove screws M and L, K and J. Also remove screws D, E, F and G holding door side hinges and replace at J, K, L and M as shown in illustration. Screws D, E, F and G should then be placed In positions M, L, K and J. Note: Hinges replaced diagonally, do this one at a time to avoid confusion. 9. Replace the glass and inner panel and replace screws H and I. Place the handle into position and replace screws A, B and C. Note: If round door spacers at the handle have become dislodged, replace using the double sided tape provided. Replace all fibre washers. 10. Transfer the door striker from the right ‘11’ side to the left ‘10’ side by interchanging the door striker and upper blanking screw only. Do not remove the adjacent lower screw fixings. Place door on bottom hinge and place top hinge in position, tighten screws No.5 and No.6. Replace screw No.8 and tighten screw No. 7. 11. Some adjustment of the door striker may be necessary at this stage. With the door moved to a position where the door catch meets the striker, the striker must be located in the centre of the door catch aperture. If the striker does not locate centrally in the door catch, vertical adjustment may be obtained by slackening the door striker locknut and the posi-s...