Votes - 3, Average rating: 4.3
(
)
)
|
manual abstract
Power control On / Off 0 00 0 Timer control key Power indicator and residual heat indicator for each heating zone Booster key Power control Lock control Lock indicator Using Your Hob NEVER allow aluminium foil to be in contact with the hob surface when in use. Setting the Hotplate Step 1 Place the saucepan centrally on the required heating zone. Step 2 Switch on the power using the on/off sensor . Step 3 Press the required heating zone selection sensor and using the sensors select the required heat setting. Step 4 When you have finished cooking, return the heating zone to 0 by pressing the key and switch off the power using the on/off sensor . DO NOT allow young children near to the hob when the it is in use as the surfaces get extremely hot! Guide To Using The Hotplates Setting Type Of Food 1 Melting butter, chocolate,etc. 2 or 3 Heating food gently. Keeping small amounts of water simmering. Heating sauces containing egg yolk and butter. Simmering stews, meat, fish vegetables and fruit. 4 Heating solid and liquid foods. Keeping water boiling. Thawing frozen vegetables. Making 2-3 egg omelettes. 6 or 7 Cooking food just above simmering. Maintaining a rolling boil for preserve making. 8 or 9 Sealing meat and fry fish. 9 Frying potatoes. Boiling water. Deep fat frying Dissolving sugar for preserve making. Deep Fat Frying Safely 1. Use a deep pan, large enough to completely cover the appropriate heating area. 2. Never fill the pan more than one third full of oil. 3. Never leave oil or fat unattended during the heating or cooking period. 4. Never try to fry too much food at a time, especially frozen food. This lowers the fat temperature too much resulting in greasy food. 5. Always dry food thoroughly before frying, then lower it slowly into the hot oil or fat. Frozen foods in particular will cause the fat to froth and spit if added too quickly. 6. Never heat fat or fry with a lid on the pan. 7. Keep the outside of the pan clean and free of streaks of oil or fat. Using Your Hob Using the heating zones: 1 2 3 0 Press the On/Off key to switch on the hob. The power indicators display ‘0’. Press the heating zone control key of your choice (eg. the rear right heating zone). The corresponding power indicator displays ‘0‘. Press the key to display the required power level (from 1 to 9). OR Press the key briefly, to go direct to the maximum power level (9). NOTE: To speed up the temperature rise of the rear right and front left heating zones, press the Booster key, the power indicator will display ‘P’. Any power level from 1 - 9 can be used with the booster function which increases the heating zone to 3000W. The booster function stops automatically after 4 minutes, however the power level will remain at the chosen level. The maximum power of the rear left and front right heating zones is limited to 600W whilst the rear right and front left heating zones are boosted to 3000W. Using Your Hob Using the heating zones: 4 00 To switch off the hob at the end of cooking: Press the key until the power level returns to ‘0’. Press the the hob. and keys simultaneously to switch off OR Press the key. NOTE: Your hob is equipped with 4 residual heat indicators. The power indicator for each heating zone shows ‘H’ while the temperature of the heating zone exceeds 60°C after the power is switched off. This helps prevent the risk of burns. Using Your Hob Programming a cooking duration: It is possible to programme the cooking time of a heating zone for a maximum duration of up to 99 minutes. Select the heating zone and desired power level and then proceed as follows: 3 25 2 25 1 00 Press the key to access the programming function. The corresponding indicator light flashes. Press the key to display the required cooking duration (maximum 99 minutes). Important: Press the key again to confirm the programming operation. NOTE: The timer starts counting down immediately. An audio signal sounds at the end of the cooking time and the heating zone switches off. Press the key to switch off the power to the hob. Using Your Hob Multiple programming: It is possible to programme all four heating zones at the same time. Follow the previous step by step procedure to programme the first heating zone, then proceed as follows: 2 45 1 25 A heating zone is already programmed, the corresponding indicator light is on and the timer display is activated. It starts flashing slowly as soon as you start to programme another heating zone. Select the second heating zone, then press the key to access the programming function. Press the key to display the required duration. Press the key again to confirm the programming operation. NOTE: The indicator light that corresponds to the heating zone being programmed flashes slowly and then remains lit once the programming operation is confirmed. The indicator light that corresponds to the previously programmed heating zone flashes. To display the remaining time programmed for a heating zone, select it by pressing the relevant h...