Votes - 4, Average rating: 4.3
(
)
)
|
manual abstract
6. Any repairs to this appliance should be carried out by a qualified service person. 7. Under no circumstances should this appliance be modified. Parts having to be removed for servicing must be replaced prior to operating this appliance again. 8. Do not use outdoors. 9. This appliance is not intended for use in bathrooms, laundry areas and similar indoor locations. Never locate this appliance where it may fall into a bathtub or other watercontainer. 10. Do not run cord under carpeting. Do not cover cord with throw rugs, runners or the like. Arrange cord away from traffic areas and where it will not be tripped over. 11. To disconnect this appliance, turn controls to the off position, them remove the plug from the outlet. 12. Connect to properly grounded outlets only. 13. This appliance, when installed must be electrically grounded in accordance with local codes, with the current CSA C22.1 Canadian Electric codes or for USA installations, follow local codes and the National Electrical Code, ANSI/NFPA No. 70. 14. Do not insert or allow foreign objects to enter any ventilation or exhaust opening as this may cause an electric shock, fire or damage the appliance. 15. To prevent possible fire, do not block air intakes or exhaust in any manner. Do not use on soft surfaces, like a bed, where openings may become blocked. 16. This appliance has hot and arching or sparking parts inside. Do not use it in areas where gasoline, paint or flammable liquids are used or stored. This appliance should not be used asa drying rack for clothing, nor should Christmas stockings or decorations be hung on or near it. 17. Use this appliance only as described in this manual. Any other use not recommended by themanufacturer may cause fire, electric shock or injury to persons. 18. Avoid the use of an extension cord because the extension cord may overheat and cause a risk of fire. However, if you have to use an extension cord, the cord shall be 14 ga minimum size and rated not less that 2025 watts. The extension cord must be a three wire cord with grounding type plug and cord connector. The extension cord shall not be more than 20 feet (6m) in length. SPECIFICATIONS Dimensions W x D x H 26” x 15.4” x 28.5” 66 cm x 39 cm x 72.4 cm Net Weight Gross Weight 61 lbs / 27.7 kg 68.8 lbs / 31.3 kg Voltage 120 V Frequency 60 Hz Watts 1400 W Heater Rating 4770 BTU ELECTRICAL CONNECTION A 15 Amp, 120 Volt, 60 Hz circuit with a properly grounded outlet is required to operate this appliance. Preferably, the stove will be on a dedicated circuit as other appliances on the same circuit may cause the circuit breaker to trip or the fuse to blow when the heater is in operation. The unit comes standard with a 6 ft (1.8 m) long 3 wire cord, exiting out the back of the stove. Plan the installation to avoid the use of an extension cord. If an extension cord must be used, it must be a minimum 14 ga, 3 wire with grounding type plug and connector and rated not less than 2025 watts. The extension cord shall not be more than 20 ft (6 m) in length. WARNING: Electrical outlet wiring must comply with local building codes and other applicable regulations to reduce the risk of fire, electrical shock and injury to persons. WARNING: Do not use this stove if any part of it has been under water. Immediately call a qualified service technician to inspect the stove and replace any part of the electrical system which has been under water. SERVICE INSTRUCTIONS SERVICE INSTRUCTIONS FOR YOUR SAFETY Service must be performed by a qualified service agency. REPLACING THE LIGHT BULBS This stove uses 2 clear 120 Volt, 40 Watt, E-12 socket base light bulbs (small base, chandelier candle type bulbs). The access plate is located on the back of the unit. Forconvenience, if one of the light bulbs burns out, it may be easier to replace both of the lightbulbs at the same time. WARNING: Do not exceed 40 Watts per bulb. Use of higher rated bulbs may result in afire, causing property damage, personal injury or loss of life. 1. Turn off the power to the unit. 2. Let the stove cool if it has been operating. 3. Turn the stove so you are facing the back of the stove. 4. Look for the access plate with the gold printing on it. 5. Remove the 3 screws holding the access plate in position. Once you haveremoved the 3 screws, lift the access plate so the 2 positioning tabs come freeof their slots. Once you have removed the access plate you can see and access the2 40 watt chandelier bulbs. 6. Remove each light bulb by unscrewing them out of the bases, turning them counterclockwise. You can use one hand to hold the light socket in place, if required. 7. Install the new light bulbs by turning each light bulb into the base clockwise. You can use one hand to hold the light socket in place, if required. 8. Replace the access plate by inserting the 2 tabs, pushing the plate up against the stove back, and inserting the 3 screws. 9. Turn the stove back so you are facing the front of the stove. 10. Turn the power on...