Votes - 3, Average rating: 4.7
(
)
)
|
manual abstract
Connect the iron to the mains electricity supply Plug in the iron. The warning light goes on and indicates that the iron is heating up. As soon as the light goes out, the set temperature has been reached and the iron is ready for use. 4 ADJUSTABLE STEAM FUNCTION Set the variable steam control to required steam volume. Steam can only be produced when the thermostat is aligned to l l l or max. (red zone). Allow iron to heat up (light goes out) before activating the variable steam control. Anti-drip system (depending on model) The anti-drip system reduces the steam volume when the set temperature is too low. This helps prevent any water dripping from the soleplate. Iron ready for steam ironing Steam generation starts when the iron is held horizontally Steam stop Steam generation can be interrupted: ¦ by setting the iron on its heel ¦ by pushing the steam control slide fully to the left. 5 SPRAY FUNCTION Laundry can be spray dampened as soon as there is water in the tank. ¦ Press spray button down: slowly = spray shot fast and strongly = spray mist 6 SHOT OF STEAM While ironing, firmly press down the shot of steam button. A strong shot of steam penetrates deeply into the fabric. Allow an interval of at least 4 seconds between steam shots. DM 900 7sprachig 7 Vertical steam jet The iron can be used vertically. This is ideal for removing wrinkles from clothing on hangers, curtains, wall tapestries, etc. Important! Never steam or iron clothing that is being worn. DRY IRONING Push the variable steam control fully to the left (Position “min“). AFTER IRONING Unplug the iron. Set the variable steam control to max. and empty any water left in tank. Then set the variable steam control to min. and leave the iron to cool down. 8 Iron with cord storage ¦ For storage the supply cord can be wrapped around the integrated cord storage feature once the iron has cooled off completely. ¦ Always store the iron on its heel to protect the soleplate. CLEANING AND MAINTENANCE ¦ When necessary use a damp cloth to clean the cool iron, then wipe dry. ¦ Read the information in POINTS TO NOTE. Cleaning the soleplate For the stainless steel soleplate we recommend the Rowenta soleplate cleaner PC05. This is available from Rowenta dealers. ¦ The high quality soleplate of your iron makes ironing easier and protects your laundry. When not being used the iron should always be placed on its heel. Do not rest it on a rough surface. Do not scratch or scrape the soleplate. Do not use strong or abrasive detergents for cleaning. 9 Self-clean function ¦ It is important to activate the iron's Self clean function every two weeks to clean the steam chamber. If the water in your area is very hard we recommend weekly cleaning. Fill the tank to half, push the steam control slide fully to the left and allow the iron to heat up to maximum temperature. Hold the iron horizontally over a sink, press the self-clean button beyound the max. position to “Self-clean“ and hold it there. ¦ Initially a great deal of steam will be expelled. After a few seconds this is followed by steam and water, which rinses dirt and scale particles out of the steam chamber. Release the self-clean button after about 1 minute on position min. Unplug the iron, allow it to cool off completely and wipe the soleplate with a damp cloth. Plug in the iron again, allow it to heat up and hold it over the sink for a moment to release steam. ¦ The self-clean function helps prevent the drip opening in the steam chamber from becoming blocked or affected by scale. Keep the function working well by opening and closing the valve several times each time you have used the iron (activate the steam control slide). Long-term descaling (Long-Life Anticalc System) Your iron is fitted with a special descaling system in the water tank, which allows you to use tap water in the tank, regardless of hardness. You can also use distilled water or the Rowenta demineraliser PC010. For distilled water we recommend mixing it in a 1:1 ratio with tap water. POINTS TO NOTE POINTS TO NOTE ¦ If the iron has not been used for a long time (e.g. several weeks) the steam channels should be cleaned and any deposits removed from the iron. To do this, hold the iron horizontally before you start to use it and allow it to produce steam for about 1 minute. Also activate the shot of steam button several times. Important: Always empty the water tank when you have finished ironing! Always remember: Battery water and water containing additives (such as starch, perfume or fabric conditioner) may not be used. Such additives can affect the properties of the steam and, at high temperatures, can form deposits in the steam chamber, which will mark the laundry when they are emitted through the steam vents. For this reason descaling liquids should not be used. SERVICE/SPARE PARTS Rowenta (U. K.) Limited has a network of Service Agents throughout the country (see enclosed Service Information leaflet). These Service Agents carry out in- guarantee repai...