Votes - 2, Average rating: 4
(
)
)
|
manual abstract
To avoid the risk of electric shock, do not disassemble the iron, take it to a qualified serviceman for examination and repair. Or, call the appropriate toll-free number listed on the cover of this manual. Incorrect reassembly can cause a risk of electric shock when the iron is used. . Close supervision is necessary for any appliance being used by or near children. Do not leave iron unattended while connected or on an ironing board. . Burns can occur from touching hot metal parts, hot water, or steam. Use caution when you turn a steam iron upside down or use the surge of steam — there may be hot water in the water tank. Avoid rapid movement of iron to minimize hot water spillage. 6 SPECIAL INSTRUCTIONS . To avoid a circuit overload, do not operate another high-wattage appliance on the same circuit. . If an extension cord is absolutely necessary, a 15-ampere and 120-volt, or 7-ampere and 220-volt cord should be used. Cords rated for less amperage may overheat. Care should be taken to arrange the cord so that it cannot be pulled or tripped over. SAVE THESE INSTRUCTIONS. POLARIZED PLUG (120V Models Only) This appliance has a polarized plug (one blade is wider than the other). To reduce the risk of electric shock, this plug is intended to fit into a polarized outlet only one way. If the plug does not fit fully into the outlet, reverse the plug. If it still does not fit, contact a qualified electrician. Do not attempt to modify the plug in any way. TAMPER-RESISTANT SCREW Warning: This appliance is equipped with a tamper-resistant screw to prevent removal of the outer cover. To reduce the risk of fire or electric shock, do not attempt to remove the outer cover. There are no user-serviceable parts inside. Repair should be done only by authorized service personnel. Note: If the power supply cord is damaged, it should be replaced by qualified personnel or in Latin America by an authorized service center. 7 JKLMO Product may vary slightly from what is illustrated. . . JKLMO . Symbols . Dry . Steam . . . . 1. Water-fill opening 2. Dry/steam selector 3. Temperature-ready light 4. Pivoting cord 5. Heel rest 6. Fabric guide 7. Water tank 8. Fabric-select dial 9. Nonstick soleplate Fabric guide 8 How to Use This appliance is for household use only. Getting Started Remove any labels, stickers or tags attached to the body or soleplate of the iron. Note: Use ordinary tap water for ironing. Do not use water processed through a water softening system. Important: For optimum performance, let the iron stand for 90 seconds before beginning to iron. TO FILL THE WATER TANK 1. Tilt the iron and using a clean measuring cup, pour water into opening until the water reaches the MAX level mark on the water tank (A). Do not overfill. Refill as needed. 2. Plug in the iron. Temperature-ready light glows when iron has reached set temperature setting. Tip: If unsure of a garment’s fabric, test a small area (on an inside seam or hem) before ironing. FOR STEAM IRONING 1. Move the dry/steam selector to the desired steam level (B). 2. Turn the fabric-select dial to appropriate setting (between 4 and 6) for your fabric (C). See fabric guide on the heel rest and read garment’s label to help you determine fabric type. The temperature-ready light glows until it reaches the appropriate temperature. It then cycles on and off during ironing. 3. When finished ironing, turn the fabric-select dial to lowest heat setting, move the selector to JKLMO and unplug the iron. Stand the iron on its heel rest and allow it to cool off. Important: Always stand the iron on its heel rest when powered on but not in use. FOR DRY IRONING 1. Make sure dry/steam selector is set to JKLMO (D). Note: It is recommended that you empty the water (see “Emptying Water Tank After Ironing”). 2. Turn the fabric-select dial to the appropriate setting for your fabric (E). See fabric guide on the heel rest and read garment’s label to help you determine fabric type. The temperature-ready light glows until it reaches the appropriate temperature. It then cycles on and off during ironing. Note: For optimum performance, let the iron stand for 90 seconds before beginning to iron. 3. When finished ironing, turn the fabric-select dial to lowest heat setting, move the selector to JKLMO and unplug the iron. Stand the iron on its heel rest and allow it to cool off. Important: Always stand the iron on its heel rest when powered on but not in use. EMPTYING WATER TANK AFTER IRONING Note: It is not necessary to empty the water after each use. 1. Turn the fabric-select dial to JKLMO. Unplug the iron. Stand the iron on its heel rest and allow it to cool off. 2. Empty the water by holding the iron over a sink with the tip pointing down. Water will empty out of water-fill opening (F). Care and Cleaning This product contains no user serviceable parts. Refer service to qualified service personnel. CLEANING OUTSIDE SURFACES 1. Make sure iron is unplugged and has cooled completely. Wipe the soleplate and outer ...