Votes - 1, Average rating: 3
(
)
)
|
manual abstract
Burns can occur touching hot hot water TO EMPTY THE IRON • Unplug iron from the electrical outlet. • Follow instructions to empty the iron. • Then, follow the instructions for filling the iron. Following this procedure will ensure that you do not overfill the iron. TO ADD WATER SELF-CLEANING In order to remove calcium and built-up particles, the self-cleaning system should be run at least once a month. • Fill the watering beaker provided to the half-full mark and then pour into the water reservoir. • Set the variable steam control (4) to the no steam position. • Insert the main plug into the wall socket. • Set the temperature control dial (9) to the maximum temperature. • Wait until the thermostat light (3) goes off and steam iron has reached preset temperature. • Remove the plug from the wall socket. • Hold the steam iron horizontally over a sink. • Turn the variable steam control (4) to “Self-Clean ” position. Hot water and steam will be emitted from the soleplate. Swing the steam iron lightly back and forth gently to allow lime and dust particles to come out. • When the water reservoir is empty, shift the variable steam control from “Self- Clean” position to “0”. • Stand the iron upright and insert the plug into the wall socket to let the iron heat up again. • Move the iron over a clean cloth to clean the and let the remaining the soleplate evaporate. CLEANING, STORAGE & MAINTENANCE • Always turn the variable steam control to ‘0’ after you have emptied the water tank. • Allow iron to cool down. • Always store the iron on the metal iron rest or in an upright position on it’s heel rest to protect the soleplate. • From time to time clean the exterior with a damp cloth and wipe dry. • If you use spray starch, wipe the soleplate occasionally with a soft damp cloth to prevent the forming of a deposit. • If the iron has not been used for a few weeks, hold the iron horizontally and allow it to steam for 2 minutes before ironing. WARNING: The anti-drip function reduces water dripping and water stains. It does not prevent water dripping or water stains if you press thesteam burst button too often or if temperature is too low. The amount of water droplets will eventually decrease after iron is used for 2 to 3 tankfulsof steaming and ironing. Iron Troubleshooting Problems Potential Reasons & Solutions Iron does not heat Iron should be plugged into a 120V AC electrical outlet only. Make sure that the plug is securely in the socket. Thermostat set too low. Turn to higher seting. Auto shut-of may be activated. Move iron gently or shake. Thermostat ready light goes On and Off This is normal. The light goes On and Of as the thermostat is switching the heating element On and Of to maintain the selected temperature. Some odor or small particles come out of steam vents of new iron This is normal. Follow instructions for first use and allow iron to steam through 2-3 fillings & press the steam burst buton occasionally to eliminate small white particles. Iron does not steam Water tank may be empty or water level is very low. Add water. Make sure that the temperature control dial and the variable steam control are correctly set. For maximum steam (setting ‘Max’ on steam control), temperature control dial should be set on ‘•••’. Always allow the iron to reach the selected temperature with the steam seting at ‘0’. Make sure the temperature control dial is set in the correct steam area and the steam control is noton ‘0’. For more steam, turn temperature dial to higher seting ( e.g. ‘•••’ and the steam control to ‘Max’). If temperature seting and steam control seting are correct and there is no steam, gentlytap the soleplate on the ironing board a few times. Move the variable steam control from ‘0’ to ‘Max’ a few times. Iron Troubleshooting (continued) Problem Potential Reasons & Solutions Water droplets coming from steam vents Iron may not be hot enough. Set thermostat to the ‘max’ position. Always allow iron suficient time to heat up (thermostat light goes off) before activating the variable steam control. Auto- Of may be activated. Move iron or gently shake. Overuse of steam burst. Allow more time between each burst. Iron may have been overfilled. Turn iron off, empty water and follow instructions for filling. Steam performance may be low if iron requires seasoning. Use regular tap water for 1or 2 tanks until steam performance improves. IMPORTANT SERVICE INFORMATION In the event that your iron fails to operate properly or if your iron needs servicing DO NOT RETURN IT TO THE STORE If the warranty period has expired, please send your iron postage pre-to the Service Dept. of EURO- PROOperating LLC at the above address. You will be advised of the cost of repair before any servicing is done unless you enclose a note indicating that you would like usto proceed with the repairs and return the iron to you C.O.D. DO NOT FORGET YOUR NAME, AND COPY SALES RECEIPT. U. S.: EURO-PRO Operating LLC, 94 Main Mill Street, Door 16, Plattsburgh, NY ...