Votes - 5, Average rating: 4
(
)
)
|
manual abstract
2. ATOMIZERSPRAY BUTTON Pressing this Button provides a defined jet of spray which gently moistens fabric. 6. WATER FILLING INLET The cover prevents dust and foreign matter from entering the water tank. It also stops any water from spilling during ironing. 3. VARIABLE STEAM CONTROL Minimum to maximum steaming for different materials. Self cleaning feature flushes internal sole plate with water. 8. STAINLESS STEEL SOLEPLATE Provides maximum glide- ability and heat retention. 4. TEMPERATURE CONTROL Turn dial to select temperature. Main temperature settings are indicated by the 1, 2 and 3 dots. (See “Ironing Chart.”) 7. BUILT-IN ANTI-CALCIUM FILTER Prevents calcium build- up and prolongs the life of the iron. 5. ANTI-DRIP FUNCTION Built-in Anti- Drip feature helps reduce water spots by cutting of water flow when the iron temperature is too low to build sufficient steam. 9. PIVOT CORD For left or right handed use. Pivots up and down; prevents dragging along the fabric. The flexible cord protector protects the cord from fraying. 10. SELF-CLEANING Flushes internal soleplate with water. WATER SPRAY The water spray is useful on fabrics with stubborn wrinkles. Press the spray button and a jet of water will spray onto the fabric being ironed. See Figure 6. The water spray can be used with dry or steam ironing as desired. OPERATING INSTRUCTIONS 7 NOTE: Before starting to iron delicate fabrics, it is best to first test the temperature of the iron on a hem or an inside seam. AUTOMATIC SHUT- OFF NOTE: If the tank runs dry, remove the plug from wall outlet. Then, fill the iron with water and re-prime the pump. The iron may be filled with water while it is hot.4. For vertical steam, press the blast of steam button while holding the iron in a vertical position. See figure 5. The vertical steam function is useful for steaming curtains and drapes while still hanging. Fig. 6Fig. 5SELECTING IRON TEMPERATURESAlways read garment labels and follow the manufacturer's ironing instructions. Refer to the "Ironing Chart" on page 9 for temperature recommendations: See figures 7 & 8.• Use low settings for synthetics. •• Use moderate settings for wool, silks, and blends. ••• Use high settings for cottons and linens. IRONING HINTSWARNING! To prevent fire, do not leave iron unattended while connected. The auto shut-off safety function of your Professional Iron is designed to engage after approx. 7 minutes of non-use. The auto shut-off indicator light will flash when the auto shut-off has activated. To reset your iron and continue ironing follow these steps. See figure 9.1) Lift the iron. 2) Holding the iron horizontally in front of you, gently rock the iron back and forth several times. This motion will reset the safety switch inside the iron. Do Not Shake the Iron. The redtemperature ready light will illuminate when the auto shut-off system has been reset. Allow time for the iron to re-heat. The redtemperature indicator light will go out when the iron is ready for use. Fig. 8Variable Steam ControlFig. 7Fig. 9• Sort articles to be ironed according to the type of fabric. This will reduce the need to adjust the temperature for different types of garments. • If you are not sure of the fiber content of a garment, test a small area such as a seam or inside hem section before ironing a visible area. Start with a low temperature setting and gradually increase to find the best setting. • When reducing the temperature to iron sensitive fabrics, allow approximately 2 minutes for the iron to cool to the new temperature setting. • Fabrics such as velour, wool, linen and silk are best ironed with an ironing cloth to prevent shine marks. OPERATING INSTRUCTIONS This appliance is for HOUSEHOLD USE ONLY and may be plugged into any 120V AC polarized electrical outlet. Do not use any other type of outlet. BEFORE FIRST USE Remove any labels, stickers or tags which may be attached to the body or the soleplate of the iron before using the iron. Before you start using your iron, read all the instructions in the manual and do the following in order to eliminate any odor and small white residue particles and to ensure optimum steam performance. 1. Fill the iron with regular tap water. (See page 6 for filling instructions.) 2. Set the temperature control dial to its highest setting and the variable steam control to “0”. 3. When the temperature ready light goes off, the iron has reached the selected temperature. Set the variable steam control to the highest setting. 4. Keep the iron in a horizontal position and allow it to steam until the water runs out. Press the blast of steam button to eliminate white residue particles. 5. Repeat this procedure for two or three fillings of water. DRY IRONING All marked settings on the temperature dial can be used for dry ironing. Slide the variable steam control lever all the way down as shown in Figure 1. This will cut off the steam flow if water is in the tank. STEAM IRONING CAUTION! DO NOT aim iron at face, towards yourself, or...