Votes - 5, Average rating: 4 ( )

Manafacture: Groupe SEB USA - T-FAL File size: 431.55 kb File name: 002ebbfb-31a9-40aa-bfc3-22c6d1f95f83.pdf Language of manual:

A little water may remain in the tank. -Wind the cord around the heel at the back of the iron. -Store the iron on its heel. FOR YOUR SAFETY • Warning ! The voltage of your electrical installation must correspond to that of the iron (220V-240V). Connecting to the wrong voltage may cause irreversible damage to the iron and will invalidate the guarantee. • This iron must always be plugged into an earthed socket. • If using a mains extension lead, ensure that it is correctly rated (10A), with an earth. • If the electrical cord becomes damaged, it must be immediately replaced by an Approved Service Centre to avoid any danger. • Never immerse your iron in water ! • The appliance must be unplugged before filling or emptying the water tank. • If the appliance falls, have it checked by a professional before using it again; unseen damage may be dangerous. • The soleplate may be very hot : - Never touch it. -Always let it cool off before putting it away. - Never leave your iron unattended when it is plugged in or while the soleplate is still hot. -Always keep your iron out of the reach of children. NEVER DISMANTLE YOUR IRON ; ALWAYS CONTACT AN APPROVED SERVICE CENTRE. • This product has been designed for domestic use only.Any professional use, inappropriate use or failure to comply with the instructions, the manufacturer accepts no responsibility and the guarantee will not apply. If you have any problem or queries, please contact our Customer Relations team first for expert help and advice. 5- IF THERE IS A PROBLEM Problem Water drips from the holes in the soleplate. • Possible causes The chosen temperature is too low and does not allow for • the formation of steam. You are using steam while the iron is not hot enough. • You are using the Shot of Steam button too often. • The steam flow is too high. • You have stored the iron horizontally, without emptying it and without • setting it to DRY. Solutions Set the thermostat in the coloured zone (from • .. to MAX). Wait until the thermostat light goes out. • Wait a few seconds between each use of the button. • Reduce the steam flow. • See the section "Storing your iron". • Brown streaks come through the holes in the• soleplate and stain the linen. You are using chemical descaling agents. • You are using pure distilled/demineralised or softened water. • Fabric fibres have accumulated in the holes of the soleplate and are • burning. Your linen has not been rinsed sufficiently or you have ironed a new • garment before washing it. Do not add any descaling agents to the water in the water tank. • (see section “what water to use). Carry out a self-clean and use tap-water. • Carry out a self-clean. • Clean the soleplate with a non-metallic sponge. • Vacuum the holes of the soleplate from time to time. • Ensure linen is rinsed thoroughly to remove any soap deposits or chemicals on new garments which may be sucked up by the iron. The soleplate is dirty or brown and can stain • • You are using too high a temperature. • Clean the soleplate as indicated above. the linen. See the temperature table to correctly set the thermostat. You are using starch. • • Clean the soleplate as indicated above. Always spray starch onto the reverse side of the fabric to be ironed. There is little or no steam. • • The water tank is empty. • Fill it. The anti-calc valve is dirty. • • Clean the anti-calc valve. Your iron has a build-up of scale. • • Clean the anti-calc valve and carry out a self-clean. You iron has been used dry for too long. • • Carry out a self-clean. (Depending on Model) Anti-drip function activatedWait for the soleplate to reach the correct temperature The soleplate is scratched • • You have placed your iron flat on a metallic rest-plate. • Always set your iron on its heel. Make sure that the stopper is properly closed and that the arrow • Water is running out • • You have not closed the tank points to the “closed padlock” symbol. Steam comes the iron as you finish filling • • The steam control is not set to position. • Check that the is set to the position. tank. Indicador luminoso de parada automatica (segun modelo) Varilla anticalcarea Mando de vapor Para ajustar el caudal vapor Orificio de llenado del deposito Tecla Super Pressing Para quitar las arrugas Tecla Pulverizador Para humedecer la ropa Indicador luminoso del termostato Se apaga cuando se alcanza la temperatura deseada Espanol032546- 37/03 Lea detenidamente este manual de instrucciones y guardelo. AQUASPEED .Que agua hay que utilizar? Este aparato ha sido disenado para funcionar con agua del grifo. Sin embargo, hay que realizar regularmente una limpieza automatica de la camara de vaporizacion, para eliminar la cal libre. Si el agua tiene mucha cal (pregunte en el ayuntamiento o al servicio de suministro de agua), puede mezclarse agua del grifo con agua desmineralizada de venta en cualquier drogueria y respetando las siguientes proporciones : - 50% de agua de grifo, 50% de agua desmineralizada. .Que agua hay que evitar? Dur...

Download now

Please, enter two numbers from picture: