Votes - 0, Average rating: 0
(
)
)
|
manual abstract
fragrant. Water as this could damage the appliance. However, in hard water areas, to improve the steam production and to prolong the life of your iron, mix tap water with distilled water in the following quantities: Hard water area: 1 part distilled water/ 1 part tap water Very hard water area: 2 parts distilled water/1 part tap water DO NOT use condesed water from tumble driers, air conditioning units or similar. 3. Setting the temperature Before ironing, always check the instruction label on the garment to determine the correct ironing temperature. Fabric Temperature Setting Synthetics • Silk – Wool •• Cotton – Linen ••• The temperature is set via the display screen. (K) It comprises of several icons that indicate the status of the iron Off The iron is switched off. Thermometer symbol Indicates the temperature of the sole plate. AUTO The selected ironing temperature is suitable for all types of fabrics. * The selected ironing temperature is suitable for synthetic fabrics. The selected ironing temperature is suitable for wool and silk. The selected ironing temperature is suitable for cotton and linen. The steam option is ready for use. SECURE The iron is in the automatic safety cut-out state (see automatic safety cut-out). calc clean The steam chamber needs cleaning to remove the build up of scale. *) see description of the .auto. function in the section Additional features/Special functions 1. When the iron is plugged in, the display screen lights up and runs through an icon test (they all Iight up at the same time and the iron beeps). Then the iron goes into the off state while the thermometer icon shows the temperature of the appliance. 2. To switch the iron on, press the on/set button(L) once The iron switches to auto temperature and begins to heat up. During the heat up process, the thermometer icon will show that the sole plate temperature is rising. When the iron reaches the selected temperature it will beep twice. 3. To change the selected temperature, press the on/set (I) button repeatedly. The iron goes through the following cycle: pulse pulse pulse pulse pulse off auto off With the auto option it is possible to iron all types of fabric which are suitable to be ironed. Important ! • The iron is only ready for use with steam when the steam icon appears, assuming that there is water in the tank • When the iron is cooling down,the iron indicates the drop down to the selected temperature. This can take 10 minutes from to Tips • With very delicate materials like silk and poly amide is advised to try first on a part of the garment which is not visible during wearing • Sort out your garments based on the label instructions about ironing. Start ironing garments which require the lowest temperature setting. 4. Ironing with steam The steam regulator (A) is used to adjust the amount of steam produced when ironing. 1. Make sure that there is water in the tank (D). 2. Adjust the temperature setting and then set the steam regulator according to the table below. Steam will automatically be produced: Temperature Setting Steam Regulator Setting ••• or “auto“ maximum steam position •• medium steam position Note: At a temperature setting of “•”, the water is not hot enough to produce steam so the steam regulator should be set to the “0” position to avoid water dripping from the soleplate (E). 5. Ironing with shot of steam This can be used to remove stubborn wrinkles or to press in a sharp crease. It cannot be used on a synthetic setting for delicate items. 1. Set the temperature to the “•••” or “auto” position with the on/ set button (I). 2. Set the steam regulator (A) to the maximum steam position. 3. Press the jet of steam (L) button on the handle repeatedly at intervals of 5 seconds. 6. Vertical steaming with shot of steam This can be used to remove creases from hanging clothes, curtains etc. It cannot be used on a synthetic setting for delicate items. WARNING! Never spray or aim steam at people! 1. Set the temperature to the “•••” or “auto” position with the on/ set button (I). 2. Set the steam regulator (A) to the maximum steam position. 3. Hold the iron in an upright position 10 - 20 cm away from the object being steamed. 4. Press the jet of steam (L) button at intervals of 5 seconds. 7. Ironing without steam This function enables the iron to be used for dry ironing. 1. Set the steam regulator (A) to the position. 2. Select an appropriate temperature for the type of material being ironed. 8. Spray This can be used to remove stubborn wrinkles. 1. Do not use the spray function with silk as staining may occur. 2. Make sure that there is water in the tank (D). 3. When ironing, press the spray button (M) and water will spray out of the spray outlet (C) onto the garment. 9. After finishing each ironing session 1. Unplug the iron from the mains socket. 2. Set the steam regulator (A) to the position. 3. Open the water tank cover. 4. Hold the iron with the point facing up and shake it gently until all the water has co...