To prevent spillage of water out of the appliance in vertical position, never fill beyond the «max» water level mark (K)! 7 Ironing without steam This function enables the iron to be used for dry ironing. 1. Set the steam regulator (C) to the «0» position. 2. Select an appropriate temperature for the type of material being ironed. 8 Spray This can be used to remove stubborn wrinkles. 1. Do not use the spray function with silk as staining may occur. 2. Make sure that there is water in the tank (G). 3. When ironing, press the spray button (B) and water will spray out of the spray outlet (E) onto the garment. 9 After finishing each ironing session 1. Unplug the iron from the mains socket. 2. Set the steam regulator (C) to the «0» position. 3. Open the water tank cover (M). 4. Hold the iron with the point facing up and shake it gently until all the water has come out. 5. Set the iron aside in a vertical position to cool down. 6. Coil the power cable (N) loosely around the heel of the iron, before storing. 7. Store the iron in an upright position. 10 Multiple de-scaling system This range of irons is equipped with the following de-scaling features “AntiCalc”. A. self-clean Each time you use the steam regulator (C), the “self-clean” system cleans the mechanism of any scale deposits. B. calc’n clean The “calc‘n clean” function helps to remove scale particles out of the steam chamber. Use this function approximately every 2 weeks, if the water in your area is very hard. Fill the water tank, set the temperature control (J) to the “max”. position and plug in the iron. After the necessary warm-up period, unplug the iron and hold it over a sink. Take out the steam regulator (C) by turning it to the position while pressing it down. Gently shake the iron. Boiling water and steam will come out, carrying scale or deposits that might be there. When the iron stops dripping, reassemble the steam regulator in reverse order and move it to the «0» position. Heat up the iron again until the remaining water has evaporated. If the steam regulator needle is soiled, remove any deposits from the needle tip with vinegar and rinse off with clean water. C. anti-calc cartridge (model dependent) The anti-calc cartridge has been designed to reduce the buildup of scale produced during steam ironing, helping to extend the useful life of your iron. Nevertheless, the “anti-calc” cartridge cannot remove all of the scale that is produced naturally over time. 11 Anti-drip system „Drip Stop“ All the irons in this range are equipped with an anti-drip system. This will automatically stop the iron producing steam when the selected temperature setting is too low to prevent water from dripping out of the soleplate. You may hear a clicking sound when this system is in operation. Additional Features (Model Dependent) Auto shut-off “Secure” Some irons in this range are equipped with an auto-shut off system. The “secure” auto shut-off function switches off the iron automatically when it is not being used, thus helping to prevent accidents and saving energy. When the appliance is first plugged in, this function will be inactive for the first 2 minutes to allow it to reach the set temperature. If during ironing, the iron is not moved for a certain length of time, the iron will automatically switch off. The length of time will depend on the position the iron has been left in: Horizontally (flat) or on its side: 30 seconds Vertically (upright): 8 minutes The pilot light (O) on the top of the handle will flash when auto shut-off has been activated. To switch the iron back on, move it gently from side to side. The light will stop flashing. Fabric-protection soleplate cover The fabric-protection cover is used for steam-ironing delicate garments at maximum temperature without damaging them. Use of the protector also does away with the need for a cloth to prevent shine on dark materials. It is advisable to first iron a small section on the inside of the garment to see if it is suitable. To attach the fabric protector to the iron, place the tip of the iron into the tip of the fabric protector and press the rear of the protector upward until you hear a click. To release the fabric protector, pull down on the clip at the rear and remove from the iron. The protective cover can be purchased from After-sales. Accessory code (After-sales) 650808 Metal ironing tip The metal tip (F) helps to improve the ironing of collars and pockets. Tips to help you save energy Steam production consumes the most energy. To help minimise the energy used, follow the advice below: • Start by ironing the fabrics that require the lowest ironing temperature. • Regulate the steam according to the selected ironing temperature. • Only use steam if necessary. If possible, use the spray function instead. • Try to Iron the fabrics while they are still damp and reduce the steam setting. Steam will be generated from the fabrics rather than the iron. If you tumble dry your fabrics before ironing them, set...

Other models in this manual:
Irons - TDA3610GB/01 (749.26 kb)
Irons - TDA3640GB/01 (749.26 kb)