Votes - 2, Average rating: 3
(
)
)
|
manual abstract
To check the level of water, grasp the Tank vertically. 4. To re-install the Tank, set the Tank onto the main body and press into place until a click sound is heard. 5. The water level can be observed through the transparent part of the Tank, when iron is placed vertically. When the water level becomes low, refill the Tank, following the procedure described in steps 1 to 4 above. Note: Most tap water can be used in this iron. If water is very hard, distilled or demineralized water should be used. Do not use water processed through home water softening systems because this water contains minerals that may be harmful to the iron. Do not use water additives or substitute water such as linen or scented water in the steam iron. They can stain fabrics or damage the iron. HOW TO USE AS A STEAM IRON 1. Fill the iron as described in " HOW TO FILL WITH WATER". 2. Position the iron vertically and be sure the Temperature Selector Dial is set to" OFF". 3. Plug the AC Cord into the electrical outlet. 4. Set the Temperature Selector Dial to the" " or 11 "(steam) zone. 6 " " zone: Low Steam, for thin or delicate fabrics requiring a small amount of steam. " zone: High Steam, for fabrics requiring a lot of steam (i. e. thick materials, items with stubborn wrinkles). 5. Preheat the iron until the Indicator Light goes out, usually about 1-2 minutes. This Light will go on and off during ironing to indicate the temperature chosen by the Temperature Selector Dial is being maintained. 6. Hold the iron horizontally and move the Steam/Dry Selector into the steam position. Steam/Dry Selector is regulated as follows. NOTE: 3 Positions Steam/Dry Selector. --;-i-v Dry Low Steam High Steam (Right: for High Steam, Center: for Low Steam ) Temperature Zone Steam/Dry Selector Position £#3 | ^ o & or 7. Whenever the iron is positioned vertically, the steaming action will stop. A CAUTION Do not use the Steam/Dry Selector at low or high steam positions until the Thermostat Operating Indicator Light turns off after setting the Temperature Setting Dial within the steam range. Otherwise hot water may leak from the Soleplate and burns may result. HOW TO USE 'JET-QF-STEAM11 FEATURE The"Jet-of-Steam"feature provides extra steam which goes deep into the garment and is helpful for removing stubborn wrinkles. The"Jet-of-Steam" feature operates properly only in the" " indication area of the Temperature Selector Dial when steam or dry ironing( If used at lower setting, water spotting will occur because the iron is not hot enough to change water to steam ). If you have not used the " Jet-of-Steam 11 feature for a long time, it is necessary to clean the inside of the iron before using this feature on any clothes to be ironed. Simply test the "Jet-of-Steam" feature several times away from the ironing board and clothes to be ironed. This will prevent brown spotting or water spotting on the clothes. -7- 1. Fill the iron as described in " HOW TO FILL WITH WATER 2. Position the iron vertically and be sure the Temperature Selector Dial is set to " OFF Plug the AC Power Cord into the electrical outlet. 3. Set the Temperature Selector Dial to the" " indication area. 4. Preheat the iron until the Indicator Light goes out, usually about 1-2 minutes. 5. Simply pump the " Jet-of-Steam Button " when steam is desired. Pump the " Jet-of-Steam Button " several times at the beginning of each ironing session. 6. Allow at least 2-5 seconds between uses of "Jet-of-Steam Button " to prevent water spotting. Use a press cloth if necessary. ACAUTIOlT Do not use "Jet-of-Steam Button " until the Thermostat Operating Indicator Light turns off after setting the Temperature Selector Dial to" 6 ". Otherwise hot water may leak from the Soleplate and burns may result. HOW TO USE "VERTICAL STEAM" FEATURE To get better results when using vertical steam, hang the garment on a clothes hanger. Curtains and drapes may also be steamed once they're hung. Hold the iron away from your body, close to but not touching the fabric. Pull the fabric tight with your free hand and pump the Vertical Steam Button(Jet-of-Steam Button) at 2-5 seconds intervals as you pass the iron over the wrinkled fabric. A WARNING Never iron clothes on the body or point your iron at anyone when steaming. Keep hands and body away from steam areas while using vertical steam feature. HOW TO USE THE SPRAY FEATURE Before using the spray feature, check the fabric label for ironing instructions because some fabrics may be spotted or stained with moisture. The spray feature is particularly helpful for removing stubborn wrinkles and where extra dampening is needed. The spray may be used with steam or dry ironing. -8- 1. Simply pump the Spray Mist Button when spray is desired. If the spray doesn't work immediately, keep pumping * until it does. ' 2. To get a finer spray, pump the Button vigorously. To get a more powerful spray, pump the Button more slowly. For best r...