Votes - 4, Average rating: 4 ( )

Manafacture: GE File size: 535.46 kb File name: 840084900_1068235526528.pdf Language of manual:

3 1 2 4 6 8 3 10 9 5 7 840084900 Ev01 5/24/01 1:44 PM Page 4 Using Your Iron To Dry Iron 1. Plug iron into electrical outlet. The Auto Shutoff Reset Button/Light will come on. If the plug will not fit, read about the polarized plug in “Consumer Safety Information.” 2. Turn the Temperature/Steam Dial to a setting in the Dry Iron range, settings 1-3. As an example, the illustration shows the iron set at 2 (Nylon). NOTE: To dry iron at setting 4 and higher, empty all water from the iron. 3. Preheat for about four minutes before beginning to iron. 4. The iron will automatically shut off one hour after the iron is plugged in and the Auto Shutoff Reset Button/Light will go out. To turn the iron back on, press the Auto Shutoff Reset Button/Light located on the top of the handle. 5. When finished ironing, turn the Temperature/ Steam Dial to 0 (OFF) and unplug iron. To Steam Iron 1. Fill water tank following instructions in “Filling the Water Tank.” 2. Plug iron into electrical outlet. The Auto Shutoff Reset Button/Light will come on. If the plug will not fit, read about the polarized plug in “Consumer Safety Information.” 3. Turn the Temperature/Steam Dial to a setting in the Steam Iron range, settings 4-9. As an example, the illustration shows the iron set at 7 (Rayon). 4. Preheat for about four minutes before beginning to iron. 4 5. The iron will automatically shut off one hour after the iron is plugged in and the Auto Shutoff Reset Button/ Light will go out. To turn the iron back on, press the Auto Shutoff Reset Button/Light located on the top of the handle. 6. When finished ironing, turn the Temperature/ Steam Dial to 0 (OFF) and unplug iron. Allow to cool and empty water from water tank. See “Storing Your Iron.” 840084900 Ev01 5/24/01 1:44 PM Page 5 Filling the Water Tank Water Window 1. Make sure iron is unplugged. 2. Regular tap water should be used. In areas with extremely hard water, the use of distilled or filtered water is highly recommended. 3. Slowly pour water into water fill opening until water level reaches the top of the Water Window (8 ounces). Never overfill. NOTE: Never place anything in your iron except water. Products like liquid starch will damage your iron and clothing if placed in the water tank. Temperature Dial and Fabric/Setting Chart Setting To Iron Ironing Instructions 0 Dry IronOff/Clean 1 Acetate Dry iron on the wrong side of the fabric. 2 Nylon Dry iron; use spray if necessary. 3 Acrylic Dry iron; use spray if necessary. 4 Silk, Lycra Iron on the wrong side of the fabric. Steam Range 5 Wool Use a pressing cloth and steam iron. 6 Polyester Iron while fabric is still damp. 7 Rayon Iron on the wrong side of fabric. 8 Cotton Iron while still damp. 9 Linen Iron on wrong side while fabric is still damp. NOTE: To dry iron on settings 4-9, empty all water from the tank. Ironing Tips • Always check fabric content before ironing. If the fabric is a blend, use the lower temperature setting. • If the fabric content is unknown, use the lowest temperature setting and test on an inside seam of the garment. • If ironing several items, start ironing the items which need the lowest temperature setting first. An iron heats • To maintain the quality of the soleplate, never iron over zippers, pins, buttons, or anything metal. • Use caution when ironing around plastic buttons and zippers as these may melt. up much faster than it cools down. 5 840084900 Ev01 5/24/01 1:44 PM Page 6 Optional Features (on selected models) Auto Shutoff Reset Button/Light Auto Shutoff Reset Button/Light 1. The timing of the automatic shutoff starts when the iron is plugged in. The Auto Shutoff Reset Button/Light will come on. 2. About one hour after the iron is plugged in, the light in the Auto Shutoff Reset Button/Light will go out which means the iron has automatically shut off. 3. Press the Auto Shutoff Reset Button/Light. This will turn the iron on for another hour and the light will come back on. 4. If the iron is plugged in and the Temperature/Steam Dial is turned to 0 (OFF), the automatic shutoff is still activated. Blast of Steam & Spray Blast of Steam Spray 1. To use Blast of Steam, the Temperature/Steam Dial must be set in the steam range. 2. To get a blast of steam, press the Blast of Steam Button. Do not press button continuously. Press once every two seconds. Some time is needed for the iron to create the steam. Please use iron carefully, as steam is hot and can cause burns or serious injury. 3. To spray a mist of water, press the Spray Button to dampen wrinkles that are difficult to remove. 6 840084900 Ev01 5/24/01 1:44 PM Page 7 Self-Clean System 1. Fill the water tank with water (8 ounces). 2. Plug in iron and turn Temperature/ Steam Dial to highest setting. Let iron preheat four minutes. 3. Leave Temperature/Steam Dial at highest setting and unplug iron. Hold iron in ironing position over a sink. Repeatedly push the Blast of Steam Button to aid in the cleaning process. 4. Be careful. Steam and hot water will p...

Download now

Please, enter two numbers from picture: