Votes - 3, Average rating: 4 ( )

Manafacture: Bosch File size: 5.25 mb File name: Language of manual:

If your water is hard, increase the frequency. Do not use descaling agents for rinsing out the boiler, as they could damage it. 1. Check that the appliance is cold and unplugged for more than 2 hours, and that the removable water tank (1) is empty. 2. Place your appliance on the edge of your kitchen sink. 3. Unscrew the boiler drainage plug located on the bottom of the appliance using a coin. 4. Holding your steam generator in upside down position, and using a jug, fill the boiler (in the base unit) with 1/4 litre of water 13 en 5. Shake the base unit for a few moments and then empty it completely over a sink or bucket. To obtain the best result, we recommend that this operation is done twice 6. Important: before re-closing, make sure no water remains in the boiler. 7. Replace and tighten up the boiler drainage plug with a coin Intelligent steam This ironing system has intelligent steam control, which provides additional steam depending on the user demand. Cleaning & Maintenance 1. After ironing, pull out the plug and allow the appliance to cool down before cleaning. 2. Wipe the housing, handle and iron body with a damp cloth. 3. If the soleplate is soiled with dirt or scale, clean it with a damp cloth. 4. Never use abrasive products or solvents. Important: • Always unplug the appliance from the mains supply before carrying out any cleaning or maintenance operation on it. Storing the appliance (D) 1. Always allow the appliance to cool down before storing it. 2. Set the switches for main power and steam boiler to the «Off/Stop» position and disconnect the connection. 3. Place the iron on the iron pad, standing on the soleplate. 4. Empty the water tank and store the mains cable on the cord rewind facility. Tidy the steam hose on the handle of the iron using the cord clip provided (12). Do not wrap the cords too tight. Trouble shooting Problem Possible causes Solution The steam generator does not come on. • There is a connection problem. • The steam tank and/or main power button is not switched on. • Check the mains cable, the plug and the socket. • Press the buttons for main power (6) and steam tank (4) «On/Start». The iron does not heat up. • The main power button is not switched on. • The temperature control knob is set to the «min» position. • Press the main power button (6) «On». • Set the temperature control knob (13) to the desired position. The iron begins to smoke when switched on. • During first use: Certain components on the appliance have been lightly greased at the factory and may produce a little smoke when initially heated. • During later use: the soleplate may be soiled. • This is completely normal and will stop after a short while. • Clean the soleplate according to the cleaning instructions in this manual. Water flows through the holes on the sole plate. • The steam function is being used before it has reached temperature. • The water is condensing inside the pipes because steam is being used for the first time or has not been used for a long time. • Reduce the steam flow when ironing at low temperatures (Variable steam control (3)). • Point the iron away from the ironing area and press the steam release button (15) until steam is produced. 14 en Problem Possible causes Solution Dirt comes out through the sole plate. • There is a build-up of scale or minerals in the steam tank. • Chemical products or additives have been used. • Use tap water mixed 50% with distilled or demineralised water. • Clean the sole plate with a damp cloth. • Never add products to the boiler water. The iron does not produce any steam. • The boiler is not switched on or the water tank is empty. • The water tank is not fitted onto the steam tank correctly. • The steam regulator is set to the minimum position. • Set the switch (4) to the «Start» position and/or fill the water tank. • Fit the water tank back onto the steam tank correctly (you will hear a click). • Increase the steam flow by turning the steam control (3). The ironed garment turns dark and/or sticks to the soleplate. • The selected temperature is too high and has damaged the garment. • Select a suitable temperature for the material being and clean the sole plate with a damp cloth. The soleplate turns brown. • This is a regular consequence of usage. • Clean the soleplate regularly with a damp cloth. The appliance makes a pumping sound. • Water is being pumped into the steam tank. • The sound will not stop. • This is normal. • If the sound will not stop, do not use the steam generator and contact an authorised technical service centre. Loss of pressure during ironing. Steam release button activated during a long period of time. Use the steam release button (15) with intervals. This improves the ironing result as the textiles will be dried and stay smooth better. Water leakage from the boiler Drainage plug located at the bottom of the appliance is loose. Tighten up boiler drainage plug with a coin Warranty conditions ...

Download now

Please, enter two numbers from picture: