Votes - 2, Average rating: 4.5
(
)
)
|
manual abstract
Accepts Tap Water -Eliminates the necessity of keeping distilled water on band for ironing. Comfortable Ergonomic Handle -Provides a more comfortable grip and easy handling. Patented MOTION SMART’” Auto-Off -Automatically turns the iron off if it is not moved after 15 minutes in the upright position or after 30 seconds in the ironing position. Power Indicator light - Lights steadily to let you know the iron is plugged in; blinks to let you know that the patented MOTION SMART” Auto-Off has activated; and is unlit when the iron is unplugged. Vertical Steam (Model 3040 only) -Functions like a garment steamer to remove wrinkles from bung garments or drapes. SHOT OF STEAM” (Model 3040 only) -Offers a powerful burst of steam for removing stubborn wrinkles. Retractable Cord -For easy storage and convenience. 1. SPRAY MIST Release 2. Sliding Water Reservoir Cover 3. Water Fill Hole 4. SHOT OF STEAM Button (Model 3040 only) 5. SPRAY MIST Button 6. Steam Control 7. Power Indicator Light 8. Patented MOTION SMART Auto-Off Indicator Blinking Light 9. Comfortable, Ergonomic Grip 1OA. Retractable Cord 10B. Winding Button 11. Heel Rest with Rubber Feet 12. Cord Wrap 13. Fabric Select Dial 14. Non-Stick Soleplate 15. l0-ounce, See-Through Water Reservoir Filling the Water Reservoir You must fill the water reservoir with water to use the SPRAY and SHOT OF STEAM features and to get steam out of your iron Tip: Sunbeam tests each iron at the factory to ensure that they function correctly. The test may leave a small, harmless amount of water within the water reservoir. Before you fill the water reservoir, please consider the following: • While this iron was designed for use with tap water, very hard water will reduce the performance of the iron. If your water is very hard, Sunbeam recommends that you use tap water the first time, then consider using demineralized or distilled water for subsequent use. You should use tap water once a month, however, to maintain the iron’s optimal steam performance. . Do not use water that has passed through a home water softening system. This type of water contains minerals that will decrease the performance and shorten the life of your Use demineralized or distilled water, instead. Important: When not ironing always set the Steam Control and the Fabric Select dial to OFF. To fill the water reservoir: 1. Make sure the Iron is unplugged and that both the Fabric Select dial and the Steam Control are set to OFF. Slide the water reservoir cover open and hold the iron at an angle. Fill the water reservoir with tap water until it reaches the maximum fill level (10 ounces). WARNING: To prevent the risk of burns, be careful when filling a hot iron with water. Hot metal parts, hot water and steam can cause injuries. Close the water reservoir cover. Extending the Power Cord: Hold iron with one hand and grasp plug of power cord with other hand. 2. Firmly pull power cord straight up to extend. 3. Do not allow children to use retractable cord feature as the cord may cause injury. Dry Ironing 1. Make sure that the Steam Control is set to OFF. 2. Plug the cord into a 102-Volt AC outlet. The Power Indicator will light. 3. Turn the Fabric Select dial to the Dry ironing fabric setting you desire (Silk or Synthetics) and allow the iron to heat for 2 minutes. While the Iron is heating, make sure it is sitting on its heel rest on a stable, protected surface. Tip: Refer to the Ironing Guide on Page 16 for the recommended setting for your fabric. Steam Ironing 1. Follow the instructions for “Filling the Water Reservoir” on Page 5. 2. Plug the cord into a 120.Volt AC outlet. The Power Indicator will light. 3. Turn the Fabric Select dial to the Steam ironing fabric setting you desire (Linen, Cotton or Wool) and allow the iron to heat for 2 minutes. While the iron is heating, make sure It is sitting on its heel rest on a stable, protected surface. Tip: Refer to the Ironing Guide on Page 16 for the recommended setting for your fabric. 4. After the iron has heated (2 minutes), turn the Steam Control to ON. I SPRAY The SPRAY MIST” feature dampens the fabric to aid in removing wrinkles from heavy fabrics and for setting creases. To use the SPRAY MIST feature: Press the SPRAY button firmly, SHOT OF STEAM” (Model 3040 only) The SHOT OF STEAM” feature provides an extra burst of steam for deep penetration of stubborn wrinkles. You can use this feature while Dry or Steam ironing, but the water reservoir must be at least full of water. To Use the SHOT OF STEAM” Feature: 1. Press the SHOT OF STEAM” button several times to prime the pump. 2. Place the iron on top of the wrinkle and press the SHOT OF button each time you would like an extra burst of steam. The SHOT OF feature may be used continuously with just a short pause between shots. Vertical Steam (Model 3040 only) The vertical steam feature allows your iron to function as a garment steamer. Tip: When using the vertical steam on clothing, hang the clothing on a clothes hanger fo...
Other models in this manual:Irons - 3040 (649.33 kb)